NAD S170 owner manual Front Panel

Page 10
FRONT PANEL

FRONT PANEL

1POWER: Switch off to disconnect the S170 from all AC power and exit the Standby mode. Switching POWER on both reconnects the AC and actively power-up the preamp.

2STANDBY: Illuminates when the S170 is in the Standby mode (dark when preamp is on, or powered-off).

3AUDIO: Press to select audio inputs sequentially using the VOLUME (SETUP) knob (see "Front Panel Operations," below).

4VIDEO: Press to select audio inputs sequentially using the VOLUME (SETUP) knob (see "Front Panel Operations," below).

5TAPE MONITOR: Press to engage the Tape Monitor loop. The signal present at the rear-panel TAPE MONITOR IN jacks will be heard (see "Front Panel Operations," below).

6MULTISOURCE: Press to select the signal output by the rear-panel MULTISOURCE OUT jacks using the VOLUME (SETUP) knob (see "Listening in a Remote Zone," below).

7SPEAKERS: Press to access the <Speaker setup> menu on the front-

GB

panel readout, and to select parameters using the using the VOLUME

 

 

(SETUP) knob and subsequent presses of the SPEAKERS key (see

 

"Configuring Your S170," and "Front Panel Operations," below).

8DELAY: Press to access the <Delay setup> menu on the front-panel readout, and to select parameters using the using the VOLUME (SETUP) knob and subsequent presses of the DELAY key (see "Configuring Your S170," and "Front Panel Operations," below).

9LEVELS : Press to access the <Levels setup> menu on the front-panel readout, and to select parameters using the using the VOLUME (SETUP) knob and subsequent presses of the LEVELS key (see "Configuring Your S170," and "Front Panel Operations," below).

10BRIGHTNESS: Press to dim the S170's front-panel readout; press again to restore full brightness.

11TONE: Press to adjust treble using the VOLUME (SETUP) knob; press again to adjust bass, and a third time to exit tone-control adjustment.

12MODE: Press to select listening modes sequentially using the VOLUME (SETUP) knob (see "Setting Listening Modes," and "Front Panel Operations," below).

10

Image 10
Contents S170 AV Surround Sound Pre-amplifierPRECAUTIONS SAFETY INFORMATIONEXPLANATION OF GRAPHICAL SYMBOLS INSTALLATIONMAINTENANCE SAFETY INFORMATIONELECTRIC POWER DAMAGE REQUIRING SERVICETABLE OF CONTENTS TABLE OF CONTENTSGETTING THE MOST FROM THE NAD S170 SAVE THE PACKAGING UNPACKING AND SETUPWHATS IN THE BOX CHOOSING A LOCATIONABOUT THX ABOUT THE S170E.A.R.S EASE OF USEABOUT THE S170 ABOUT THE S70 SYSTEM REMOTE CONTROLUPGRADABILITY QUICKSTART PLAY A DVD MOVIE OR MUSIC CDFRONT PANEL REAR PANEL COMPOSITE VIDEO OUT 4-6OUT MON OUT Connect toGETTING STARTED SETTING UP THE S170USING THE S70 REMOTE DEALING WITH HUM AND NOISENAVIGATING THE OSD AND MAKING CHANGES DISPLAYING THE MENUSNOTE THAT DISPLAY SETUP CONFIGURING THE S170NOTE THAT THX DEFAULT CONFIGURING THE S170AUDIO SETUP BASS/TREBLEPRESET SETUP CONFIGURING THE S170CONFIGURING THE BASS LIMITER CONFIGURING PRESETSCONFIGURING SPEAKERS CONFIGURING THE S170SPEAKER SETUP LEVEL SETUPDELAY SETUP CONFIGURING THE S170CONFIGURING LEVELS CONFIGURING DELAYSCONFIGURING THE S170 TRIGGER SETUPSELECTING SOURCES USING THE S170ADJUSTING THE VOLUME NOTE THATABOUT THE S170S LISTENING MODES USING THE S170SETTING LISTENING MODES MONOANALOG BYPASS USING THE S170EARS 2-ch.PCMReadout/OSD USING THE S170Source SELECTING LISTENING MODESABOUT THE LATE NIGHT MODE USING THE S170ADJUSTING CHANNEL LEVELS NOTE THATUSING PRESETS USING THE S170ADJUSTING THE TONE CONTROLS NOTE THATFRONT PANEL OPERATIONS USING THE S170NOTE THAT LISTENING IN A REMOTE ZONE MULTISOURCE USING THE S170CONTROLLING MULTISOURCE VOLUME NOTE THATNOTE THAT SAFETY INFORMATIONNAD LINK SYSTEM INTEGRATION RS-232TO FRONT-PANELCOMMANDS SPECIFICATIONSPOSSIBLE SOLUTIONSS CONDITIONSTEREO ANALOG BYPASS SPECIFICATIONSPHYSICAL SPECIFICATIONS OUTPUT IMPEDANCENew HTR 2 Learning Remote Control New V3.03 Operating System SoftwarePage 2001 NAD ELECTRONICS INTERNATIONAL