NAD owner manual USING THE S170, Adjusting The Tone Controls, Note That, Using Presets

Page 25
ADJUSTING THE TONE CONTROLS

ADJUSTING THE TONE CONTROLS

From the S70 remote's PREAMP menu, select [MODE/MULTI.S]; then press the [•Tone] key; "Treble" appears on the OSD and the front-panel readout. Use the remote's [Cursor up/down] to boost or cut treble by 1 dB increments. Press [•Tone] again to adjust bass, similarly using the [Cursor up/down] keys; "Bass" appears on the OSD and readout. Press [•Tone] again to exit the tone-control function. See also "Audio Setup," and "Configuring Presets," above.

NOTE THAT:

•Bass/treble settings affect only the front channels (left, center, and right), and are active in all listening modes

•Bass/treble settings imposed via the S70 remote's [•Tone] will override those stored on the <Audio setup> menu, but they are temporary: Cycling through the S170's Standby mode (or recalling the <Audio setup> menu), or recalling a Preset, will override them and revert to the settings selected by <Audio setup> or the recalled Preset.

USING PRESETS

From the S70 remote's PREAMP menu, select [PRESET 1-5]; then press the [•Preset1] through [•Preset5] key to engage the desired Preset. Keying [Exit] returns to the PREAMP menu but leaves the last-selected Preset in force.

NOTE THAT:

•The selected Preset remains in force until you select a different Preset, or cycle the S170 through its Standby mode.

•A Preset applies regardless of what source is selected, or what listening mode is in operation.

•Cycling the S170 through its Standby mode cancels any selected Preset, reverting both tone and all level settings to those set on the S70 remote's LEVELS or MODE/MULTI.S screens, or the S170 preamp's <Audio setup> OSD menu (above).

•A Preset's channel levels are added to the setup levels established on the S170 preamp's <Levels setup> OSD menu; a Preset's tone-control settings override those established on the <Audio setup> OSD menu (or the MODE/MULTI.S remote page) entirely.

USING THE S170

GB

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents AV Surround Sound Pre-amplifier S170EXPLANATION OF GRAPHICAL SYMBOLS SAFETY INFORMATIONPRECAUTIONS INSTALLATIONELECTRIC POWER SAFETY INFORMATIONMAINTENANCE DAMAGE REQUIRING SERVICETABLE OF CONTENTS TABLE OF CONTENTSGETTING THE MOST FROM THE NAD S170 WHATS IN THE BOX UNPACKING AND SETUPSAVE THE PACKAGING CHOOSING A LOCATIONE.A.R.S ABOUT THE S170ABOUT THX EASE OF USEABOUT THE S170 ABOUT THE S70 SYSTEM REMOTE CONTROLUPGRADABILITY PLAY A DVD MOVIE OR MUSIC CD QUICKSTARTFRONT PANEL COMPOSITE VIDEO OUT 4-6OUT MON OUT Connect to REAR PANELUSING THE S70 REMOTE SETTING UP THE S170GETTING STARTED DEALING WITH HUM AND NOISENAVIGATING THE OSD AND MAKING CHANGES DISPLAYING THE MENUSNOTE THAT DISPLAY SETUP CONFIGURING THE S170NOTE THAT AUDIO SETUP CONFIGURING THE S170THX DEFAULT BASS/TREBLECONFIGURING THE BASS LIMITER CONFIGURING THE S170PRESET SETUP CONFIGURING PRESETSSPEAKER SETUP CONFIGURING THE S170CONFIGURING SPEAKERS LEVEL SETUPCONFIGURING LEVELS CONFIGURING THE S170DELAY SETUP CONFIGURING DELAYSTRIGGER SETUP CONFIGURING THE S170ADJUSTING THE VOLUME USING THE S170SELECTING SOURCES NOTE THATSETTING LISTENING MODES USING THE S170ABOUT THE S170S LISTENING MODES MONOEARS USING THE S170ANALOG BYPASS 2-ch.PCMSource USING THE S170Readout/OSD SELECTING LISTENING MODESADJUSTING CHANNEL LEVELS USING THE S170ABOUT THE LATE NIGHT MODE NOTE THATADJUSTING THE TONE CONTROLS USING THE S170USING PRESETS NOTE THATFRONT PANEL OPERATIONS USING THE S170NOTE THAT CONTROLLING MULTISOURCE VOLUME USING THE S170LISTENING IN A REMOTE ZONE MULTISOURCE NOTE THATNAD LINK SAFETY INFORMATIONNOTE THAT SYSTEM INTEGRATION RS-232POSSIBLE SOLUTIONSS SPECIFICATIONSTO FRONT-PANELCOMMANDS CONDITIONPHYSICAL SPECIFICATIONS SPECIFICATIONSSTEREO ANALOG BYPASS OUTPUT IMPEDANCENew V3.03 Operating System Software New HTR 2 Learning Remote ControlPage 2001 NAD ELECTRONICS INTERNATIONAL
Top Page Image Contents