Daewoo 51M200A Connecting External Video Sources, Before Operating External Video Source

Page 14

FIRST TIME USE

CONNECTING EXTERNAL VIDEO SOURCES

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your Projection Monitor is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.

Before Operating External Video Source

The input mode is changed every time the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT terminal, then press the VID1~VID5 button as necessary to view the input source (see page 22).

NOTE: When a video signal is not received from the VIDEO INPUT JACK on the back panel of the Projection Monitor (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the Monitor will appear to be OFF.

14

Image 14

Contents Operating Guide for 51M200, 65M200, 51M200A IndexImportant Safety Instructions Do not OpenPrevention of Screen Burn Lead NoticeAccessories First Time USEViewing HOW to SET UP Your NEW Hitachi Projection MonitorLocation BestHOOK-UP Cables and Connectors Phono ConnectorFront Input Jacks Input Front Panel ControlsMagic Focus Front Panel Jacks and Connectors Monitor OUT Rear Panel JacksAudio/Video Inputs 1, 2, 3 Audio to HI-FI OutputComponent Y-PBPRInputs DVI-HDTV Input InputTypical FULL-FEATURE Setup First Time USE Rear Panel ConnectionsTips on Rear Panel Connections Connecting External Audio Devices Rear Panel of Projection MonitorConnecting External Video Sources Before Operating External Video SourceConnecting a Monaural Audio Source to INPUT1~INPUT5 Connecting a Stereo Source to INPUT1~INPUT5 Connecting AN S-VIDEO Source to Input 3, 4 DVI-HDTV Connecting a Component Source to Input 1 or 2 Y-PBPR Remote Control Remote ControlPICTURE-IN-PICTURE buttons HOW to USE the Remote to Control Your Projection MonitorPower button DAY/NIGHT buttonVID1 ~ VID5 VOLUME, Mute buttonAntenna button Satellite Receiver SAT Mode Only Size button Exit button Sleep buttonInfo button ButtonPIP button POP Mode PICTURE-IN-PICTUREPICTURE-IN-PICTURE PIP Swap button Split Mode PICTURE-IN-PICTUREPIP Mode button SplitPOP SUB Freeze with PIP OFF Freeze button With PIP onFreeze button with PIP OFF Split FREEZEwith PIP OFFDVD/VCR Button Using the Remote to Control VCR FunctionsOperating the precoded function for your VCR Precoded VCR ButtonsPrecoded CABLE/SATELLITE BOX Buttons Using the Remote to Control CABLE/SATELLITE BOX FunctionsCable CBL/SAT Button RemotePrecoded DVD Buttons Using the Remote to Control DVD FunctionsOperating the precoded function for your DVD player ON-SCREEN Display OSD Video Picture Mode VideoContrast ANT A/BPure depending on the user’s preference Reset Video SettingsColor Management Auto Color Auto Movie ModeColor Decoding Noise ReductionAudio TrebleTechnology Auto Aspect Aspect ModeAspect Vertical PositionLocks LocksMovie Ratings TV Ratings Canadian Ratings English Table Canadian RatingsEng + General Not recommended for young FrnCanadian Ratings French Table Programming is not suitable for childrenSetup Auto Digital Convergence Adjustment Magic Focus Tune UpTo Change the Color of Adjustment Point Manual Convergence Adjustment ModeTo Move Adjustment Point To Adjust the ConvergenceMenu Preference Menu PreferenceMenu Background Set The ClockSet The Inputs Set The Color System Set Virtual HD Set Black Side PanelChannel Set ClosedCaption About Your TVCare of Your Aspect Projection Monitor Your Remote Control Do notReception Problems Symptoms Useful InfoOutputs Dimensions 51M200 51M200AInputs Dial Toll Free Aspect Brand ElectronicsIndex Page Page Page Page Page QR64461