Daewoo 51M200A, 65M200 Manual Convergence Adjustment Mode, To Move Adjustment Point

Page 47

SETUP

Manual Convergence Adjustment Mode

NOTES: 1. Please turn ON your Projection Monitor for at least 20 minutes before using this feature.

2.Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode.

3.If Auto Adjust mode is selected or the Magic Focus button is pressed, all manual adjust mode settings will be erased.

Using the Remote Control, select SETUP-MAGIC FOCUS TUNE UP-MANUAL ADJUSTMENT MODE-START to access convergence crosshatch pattern. The adjustment point is indicated by the Adjustment Point Cursor.

To Move Adjustment Point

To move the adjustment point cursor using the CURSOR buttons, the Adjustment Cursor must be WHITE. Another way to move the Adjustment Point Cursor is to press the following buttons: [2] up, [4] left, [5] down, [6] right. If you use the number buttons while the adjustment point is WHITE, it will change to RED.

To Change the Color of Adjustment Point

Press the SELECT button repeatedly (WHITE-RED-BLUE-WHITE...). Green color is fixed and cannot be adjusted.

To Adjust the Convergence

Move the Adjustment Cursor to the point to be adjusted. Use the CURSOR to match the RED and BLUE colors to GREEN (reference color). Properly aligned, all three colors should appear white.

MENU

Video

Audio

Aspect

Locks

Setup

Move SEL Sel

Setup

Magic Focus Tune Up

Aligns the Red, Green, and Blue colors to correct for Magnetic Influences.

Adjustment Mode

Auto

Manual

If you want to adjust now Start

SELECT

SELECT

SELECT

Setup

Magic Focus Tune Up

Menu Preference

Set The Clock

Set The Inputs

Set The Color System

Set Virtual HD

Set Black Side Panel

Set Closed Captions

About Your TV

Move SEL Select

Adjustment Point

Cursor

Move SEL Return

If convergence is acceptable after Manual Convergence adjustment, press EXIT button to access menu mode.

117 Manual Adjust

Please Enter Number.

0.Cancel and go to Normal Mode.

1.Done and go to Normal Mode.

EXIT

2.Back to Adjust Mode

3.Factory Reset and back to Adjust Mode.

0-3.Select

Press the [0] button on the remote control to CANCEL adjusted data and return to main picture. Press the [1] button on the remote control to SAVE adjusted data and return to main picture.

Press the [2] button on the remote control to return to the manual convergence adjustment mode (crosshatch pattern). Press the [3] button on the remote control to recall the factory pre-set convergence data.

ON-SCREEN DISPLAY

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Index Operating Guide for 51M200, 65M200, 51M200ADo not Open Important Safety InstructionsLead Notice Prevention of Screen BurnFirst Time USE AccessoriesBest HOW to SET UP Your NEW Hitachi Projection MonitorLocation ViewingPhono Connector HOOK-UP Cables and ConnectorsFront Input Jacks Input Front Panel ControlsMagic Focus Front Panel Jacks and Connectors Audio to HI-FI Output Rear Panel JacksAudio/Video Inputs 1, 2, 3 Monitor OUTDVI-HDTV Input Input Component Y-PBPRInputsRear Panel Connections Typical FULL-FEATURE Setup First Time USETips on Rear Panel Connections Rear Panel of Projection Monitor Connecting External Audio DevicesBefore Operating External Video Source Connecting External Video SourcesConnecting a Monaural Audio Source to INPUT1~INPUT5 Connecting a Stereo Source to INPUT1~INPUT5 Connecting AN S-VIDEO Source to Input 3, 4 DVI-HDTV Connecting a Component Source to Input 1 or 2 Y-PBPR Remote Control Remote ControlDAY/NIGHT button HOW to USE the Remote to Control Your Projection MonitorPower button PICTURE-IN-PICTURE buttonsVID1 ~ VID5 VOLUME, Mute buttonAntenna button Satellite Receiver SAT Mode Only Size button Button Sleep buttonInfo button Exit buttonPIP button POP Mode PICTURE-IN-PICTUREPICTURE-IN-PICTURE PIP Split Split Mode PICTURE-IN-PICTUREPIP Mode button Swap buttonSplit FREEZEwith PIP OFF Freeze button With PIP onFreeze button with PIP OFF POP SUB Freeze with PIP OFFPrecoded VCR Buttons Using the Remote to Control VCR FunctionsOperating the precoded function for your VCR DVD/VCR ButtonRemote Using the Remote to Control CABLE/SATELLITE BOX FunctionsCable CBL/SAT Button Precoded CABLE/SATELLITE BOX ButtonsPrecoded DVD Buttons Using the Remote to Control DVD FunctionsOperating the precoded function for your DVD player ON-SCREEN Display OSD Video Video Picture ModeANT A/B ContrastPure depending on the user’s preference Reset Video SettingsColor Management Noise Reduction Auto Movie ModeColor Decoding Auto ColorTreble AudioTechnology Vertical Position Aspect ModeAspect Auto AspectLocks LocksMovie Ratings TV Ratings Canadian Ratings English Table Canadian RatingsEng Programming is not suitable for children FrnCanadian Ratings French Table + General Not recommended for youngSetup Magic Focus Tune Up Auto Digital Convergence AdjustmentTo Adjust the Convergence Manual Convergence Adjustment ModeTo Move Adjustment Point To Change the Color of Adjustment PointMenu Preference Menu PreferenceSet The Clock Menu BackgroundSet The Inputs Set Virtual HD Set Black Side Panel Set The Color SystemAbout Your TV Set ClosedCaption ChannelDo not Care of Your Aspect Projection Monitor Your Remote ControlReception Problems Useful Info SymptomsOutputs Dimensions 51M200 51M200AInputs Aspect Brand Electronics Dial Toll FreeIndex Page Page Page Page Page QR64461
Top Page Image Contents