Yamaha HTR-6140 owner manual Troubleshooting, 78 En, General, Problem Cause Remedy See

Page 82

Troubleshooting

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.

■General

Problem

Cause

Remedy

See

page

 

 

 

This unit fails to turn

The power cable is not connected or the

Connect the power cable firmly.

—

on or enters the

plug is not completely inserted.

 

 

standby mode soon

 

 

 

The speaker impedance setting is

Set the speaker impedance to match your speakers.

21

after the power is

turned on.

incorrect.

 

 

The protection circuitry has been activated.

Make sure that all speaker wire connections on this

11

unit and on all speakers are secure and that the wire for each connection does not touch anything other than its respective connection.

 

This unit has been exposed to a strong

Set this unit to the standby mode, disconnect the

—

 

external electric shock (such as lightning

power cable, plug it back in after 30 seconds and then

 

 

or strong static electricity).

use it normally.

 

 

 

 

 

No sound.

Incorrect input or output cable

Connect the cables properly. If the problem persists,

13-18

 

connections.

the cables may be defective.

 

 

 

 

 

 

No appropriate Audio input jack select has

Set an appropriate Audio input jack select.

34

 

been set.

 

 

 

 

 

 

 

Audio input jack select is set to “HDMI”,

Set Audio input jack select to “AUTO”.

34

 

“COAX/OPT” or “ANALOG”.

 

 

 

 

 

 

 

Audio input jack select is set to

Set Audio input jack select to “AUTO” or

34

 

“ANALOG” while playing a source

“COAX/OPT”.

 

 

encoded in Dolby Digital or DTS.

 

 

 

 

 

 

 

No appropriate input source has been

Select an appropriate input source with

33

 

selected.

O INPUT l / h(or the input selector buttons(4)).

 

 

 

 

 

 

Speaker connections are not secure.

Secure the connections.

11

 

 

 

 

 

The front speakers to be used have not

Select the front speakers with JSPEAKERS.

33

 

been selected properly.

 

 

 

 

 

 

 

The volume is turned down.

Turn up the volume.

—

 

 

 

 

 

The sound is muted.

Press JMUTE or NVOLUME +/– to resume audio

35

 

 

output and then adjust the volume.

 

 

 

 

 

 

Signals this unit cannot reproduce are

Play a source whose signals can be reproduced by this

—

 

being input from a source component,

unit.

 

 

such as a CD-ROM.

 

 

 

 

 

 

 

The HDMI components connected to this

Connect HDMI components that support the HDCP

14

 

unit do not support the HDCP copy

copy protection standards.

 

 

protection standards.

 

 

 

 

 

 

 

“SUPPORT AUDIO” is set to “Other” and

Set “SUPPORT AUDIO” to “HTR-6140” in

67

 

“HDMI” audio signals are not being

“MANUAL SETUP”.

 

 

played back on this unit.

 

 

 

 

 

 

78 En

Page 81 Page 83
Image 82
Page 81 Page 83
Contents HTR-6140 Important Safety Instructions FCC Information for US customers Example of Antenna GroundingFor Canadian Customers Serial NoContents Features Getting started Supplied accessoriesInstalling batteries in the remote control We Want You Listening For a LifetimePreparation Check the items Set up your speakersQuick start guide Press Scene 1 button Enjoy DVD playbackFront and center speakers Surround speakersFor further connections About Scene function Default assigned Scene templatesPress Scene 1 button Check the type of the connected speakersWhat do you want to do with this unit? Name ConnectionsRear panel A. modelPlacing speakers 10 EnFront B terminals Connecting speakers11 En Surround speakers Right LeftConnecting to the Speaker terminals Before connecting to the Speakers Terminal12 En Audio jacks Information on jacks and cable plugs13 En Video jacksInformation on Hdmi Audio and video signal flow14 En Connecting video components 15 En16 En Connecting other componentsConnecting a DVD player DVD player17 En Connecting a DVD recorder, PVR or VCRConnecting a set-top box PVR or VCRConnecting a multi-format player or an external decoder Connecting audio componentsConnecting a CD player and a CD recorder/MD recorder 18 En19 En Using the Video AUX jacks on the front panelPlayer Connecting the wire of the AM loop antenna Connecting the FM and AM antennasConnecting the power cable 20 EnSet this unit to the standby mode Setting the speaker impedanceTurning on and off the power 21 EnFront panel display 22 EnUsing the remote control 23 EnUsing Auto Setup Optimizing the speaker setting for your listening room24 En 25 En Speaker distance Dist 26 EnNumber of speakers SP Speaker level LVL27 En If an error screen appearsPress 8n and then press 8l / h to select SET or Cancel If Warning appears28 En Selecting the Scene templatesSelecting the desired Scene template Selected Scene template is assigned to the buttonWhich Scene template would you like to select? 29 EnVideo games AUX Game Playing Preset Scene templates descriptions 30 En31 En Customizing the preset Scene TemplatesCreating your original Scene templates Renaming the Scene templatesControlling the input source Components in the Scene mode Using remote control on the Scene feature32 En Basic operations Quick guide to contentsPlayback 33 EnSelecting the Multi CH Input component Selecting audio input jacks34 En 35 En Using your headphonesMuting the audio output Current status screen appears in the OSDAudio information Displaying the input source information36 En Video informationUsing the sleep timer 37 EnSound field program descriptions Sound field programs38 En Enjoying unprocessed input sources Straight decoding mode Enjoying 2-channel sources using Standard decoders39 En 40 En Editing sound fields parametersAdjusting the speaker level Using audio featuresAdjusting the tonal quality Enjoying high quality soundSelecting the night listening mode 42 En43 En FM/AM tuningAutomatic tuning Manual tuning Lights upManual preset tuning Automatic preset tuning44 En See Selecting preset stations on this Selecting preset stationsExchanging preset station Press and hold BPRESET/TUNING for more than 3 secondsXM Satellite Radio online information XM Satellite Radio tuning46 En XM Ready legal disclaimerBasic XM Satellite Radio operations Activating XM Satellite Radio47 En Preset Search mode All Channel Search modeCategory Search mode Direct Number Access modePreset channel number appears in the front panel display Setting XM Satellite Radio preset channels49 En 50 En Displaying the XM Satellite Radio informationDisplaying the XM Satellite Radio information in the OSD 51 En Sirius Satellite Radio tuningConnecting the SiriusConnect tuner Sirius Satellite Radio legal disclaimer52 En Activating Sirius Satellite Radio subscriptionBasic Sirius Satellite Radio operations Displaying the Sirius ID of your SiriusConnect tunerPRESET/TUNING/CH l/ hor 8PRESET/CH k/ n PRESET/TUNING/CH l/ h or 8PRESET/CH k/ n53 En PRESET/TUNING/CH l/ h or 8PRESET/CH k/ n Setting the Parental LockSetting the code number and the locked Channels 54 EnPress 8ENTER Tuning into the locked channels55 En Press 8ENTER to confirm the code numberALL 56 EnPress H Info or Odisplay PopControlling iPod in the simple remote Mode Using iPodRemote control operation Controlling iPod58 En Controlling iPod in the menu browse ModeFunction of the play information display Quick pairing Using Bluetooth componentsPairing by using SET Menu 59 EnRecording 60 EnManual setup Manual Setup Auto setup Auto Setup61 En Signal information Signal Info Using SET Menu62 En Speaker settings Aspeaker SET 63 En64 En Speaker distance CSP Distance 65 EnSpeaker level BSP Level Unit UnitCenter speaker equalizer Dcenter GEQ Audio settings Gaudio SET66 En Low-frequency effect level Elfe Level67 En Maximum volume MAX VOLInitial volume INIT.VOL Support audio S.AUDIOFor Coaxial Input jack 68 EnInput assignment For Optical Input jacks 2Decoder select mode Multi channel input setupDTS decoder prioritize setting 69 EnDisplay settings Adisplay SET 70 EnPress 9RETURN to exit from Start Pairing Bluetooth setting Ebluetooth SETPress 8ENTER to start pairing 71 En72 En XM Radio setting FXM Radio SET A. and Canada models onlySirius Satellite Radio setting XM Radio antenna XM Antenna73 En Remote control featuresControlling this unit, a TV, or other components Controlling this unit74 En Controlling other componentsInput Component Manufacturer Default Setting remote control codesRemote control code default settings 75 EnSpeaker impedance SP IMP A. and Canada models only Advanced setup76 En Only a STANDBY/ON, L Program l/ h,Tuner frequency step TU Asia and General models only 77 EnInitializing Init 78 En TroubleshootingProblem Cause Remedy See GeneralProblem Cause Remedy 79 En80 En 81 En Tuner82 En XM Satellite Radio83 En Sirius Satellite RadioDuring Auto Setup Before Auto Setup84 En 3LEVEL Error After Auto Setup1OUT of Phase 85 EnBluetooth 86 EnAdvanced setup menu appears in the front panel display Remote controlResetting the system 87 EnGlossary 88 EnNeural Surround 89 EnLFE 0.1 channel PCM Linear PCMSpecifications 90 En91 En SymbolsIndex Numerics92 En Fdynamic RangeSelection, Preset station 93 EnFront panel Power Sirius Mute MD/CD-R Tuner DVD DTV/CBL DVR List of remote control codes IiiCCE NEI TV/DVD STS HTR-6140 Front panel/Face avantRemote control/Boîtier de télécommande

HTR-6140 specifications

The Yamaha HTR-6140 is a versatile AV receiver that combines advanced audio technology with user-friendly features, making it an ideal choice for home theater enthusiasts. This robust receiver is designed to deliver high-quality sound and a rich cinematic experience, whether you are watching movies, playing video games, or enjoying your favorite music.

One of the main features of the HTR-6140 is its impressive power output, providing 610 watts across all channels. With a 7.1-channel configuration, it supports surround sound formats like Dolby Digital and DTS, allowing for an immersive audio experience that brings your media to life. The receiver also supports high-resolution audio formats, ensuring that every nuance in your favorite tracks is captured with clarity.

The HTR-6140 is equipped with Yamaha's unique YPAO (Yamaha Parametric Room Acoustic Optimizer) technology. This automated calibration system analyzes your room's acoustics and adjusts the receiver's settings accordingly. This ensures that you get optimal sound performance tailored to your specific environment, enhancing the overall listening experience.

Connectivity is another strong suit of the HTR-6140. With multiple HDMI inputs and outputs, you can easily connect all your devices, including Blu-ray players, gaming consoles, and streaming devices. It also supports 4K video pass-through, allowing for high-definition video playback without any loss in quality. Additionally, the receiver features legacy inputs like optical and coaxial, ensuring compatibility with older devices.

Yamaha's proprietary CINEMA DSP technology is integrated into the HTR-6140, offering a wide range of soundfield programs that recreate the atmosphere of famous concert halls and movie theaters. This technology enhances the spatial quality of sound, making it feel as though you are a part of the action on screen.

In terms of usability, the HTR-6140 includes a user-friendly on-screen menu and remote control. Its intuitive interface makes setup straightforward, allowing users of all skill levels to take full advantage of its capabilities. Furthermore, the receiver supports multiple audio zones, enabling you to enjoy music in different rooms simultaneously.

Overall, the Yamaha HTR-6140 is a powerful and feature-rich AV receiver that provides a wealth of options for audio and video enthusiasts. With its robust performance, advanced technologies, and ease of use, it stands out as an excellent choice for building a high-quality home theater system. Whether you're a movie buff, gamer, or music lover, the HTR-6140 offers a compelling audio experience that enhances every moment.
Top Page Image Contents