Yamaha HTR-6140 owner manual 85 En, IPod, After Auto Setup, 1OUT of Phase, 3LEVEL Error

Page 89

Troubleshooting

After AUTO SETUP

Warning message

Cause

Remedy

See

page

 

 

 

W-1:OUT OF PHASE

Speaker polarity is not correct. This

Check the speaker connections for proper

12

 

message may appear depending on the

polarity (+ or –).

 

 

speakers even when the speakers are

 

 

 

connected correctly.

 

 

 

 

 

 

W-2:OVER 24m (80ft)

The distance between the nearest speaker

Bring the speaker closer to the listening

 

and the furthest speaker is out of adjustable

position.

 

 

range.

 

 

 

 

 

 

W-3:LEVEL ERROR

The difference of volume level among

If “SWFR:TOO LOUD” or “SWFR:TOO

24, 65

 

speakers is excessive. (No level correction

LOW” appears, adjust the output volume of

 

 

is made.)

the subwoofer.

 

 

 

 

 

 

 

Readjust the speaker installation so that all

 

 

speakers are set in locations with similar

 

 

 

conditions.

 

 

 

 

 

 

 

Check the speaker connections.

11

 

 

 

 

 

 

Use speakers of similar quality.

 

 

 

 

Notes

If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.

If a warning message “W-1”, “W-2”, or “W-3” appears, corrections are made, but they may not be optimal.

If an error message “E-9” occurs repeatedly, please contact a qualified Yamaha service center.

iPod

Note

In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod (see page 19).

Status message

Cause

Remedy

See

page

 

 

 

Loading...

This unit is in the middle of recognizing

 

 

 

the connection with your iPod.

 

 

 

 

 

 

 

This unit is in the middle of acquiring

 

 

 

song lists from your iPod.

 

 

 

 

 

 

Connect error

There is a problem with the signal path

Turn off this unit and reconnect the Yamaha iPod

19

 

from your iPod to this unit.

universal dock to the DOCK terminal of this unit.

 

 

 

 

 

 

 

Try resetting your iPod.

 

 

 

 

Unknown iPod

The iPod being used is not supported by

Only iPod (Click and Wheel), iPod nano, and iPod

 

this unit.

mini are supported.

 

 

 

 

 

iPod connected

Your iPod is properly stationed in a

 

 

 

Yamaha iPod universal dock (YDS-10,

 

 

 

sold separately) connected to the DOCK

 

 

 

terminal of this unit, and the connection

 

 

 

between your iPod and this unit is

 

 

 

complete.

 

 

 

 

 

 

Disconnected

Your iPod was removed from a Yamaha

Station your iPod back in a Yamaha iPod universal

19

 

iPod universal dock (YDS-10, sold

dock (YDS-10, sold separately) connected to the

 

 

separately) connected to the DOCK

DOCK terminal of this unit.

 

 

terminal of this unit.

 

 

 

 

 

 

Unable to play

This unit cannot play back the songs

Check that the songs currently stored on your iPod

 

currently stored on your iPod.

are playable.

 

 

 

 

 

 

 

Store some other playable music files on your iPod.

 

 

 

 

INFORMATION

ADDITIONAL

 

 

English

85 En

Image 89
Contents HTR-6140 Important Safety Instructions Example of Antenna Grounding FCC Information for US customersSerial No For Canadian CustomersContents Features Installing batteries in the remote control Supplied accessoriesGetting started We Want You Listening For a LifetimeQuick start guide Set up your speakersPreparation Check the items Press Scene 1 button Enjoy DVD playbackSurround speakers Front and center speakersFor further connections Press Scene 1 button Default assigned Scene templatesAbout Scene function Check the type of the connected speakersWhat do you want to do with this unit? Rear panel ConnectionsName A. model10 En Placing speakers11 En Connecting speakersFront B terminals Surround speakers Right Left12 En Before connecting to the Speakers TerminalConnecting to the Speaker terminals 13 En Information on jacks and cable plugsAudio jacks Video jacks14 En Audio and video signal flowInformation on Hdmi 15 En Connecting video componentsConnecting a DVD player Connecting other components16 En DVD playerConnecting a set-top box Connecting a DVD recorder, PVR or VCR17 En PVR or VCRConnecting a CD player and a CD recorder/MD recorder Connecting audio componentsConnecting a multi-format player or an external decoder 18 EnPlayer Using the Video AUX jacks on the front panel19 En Connecting the power cable Connecting the FM and AM antennasConnecting the wire of the AM loop antenna 20 EnTurning on and off the power Setting the speaker impedanceSet this unit to the standby mode 21 En22 En Front panel display23 En Using the remote control24 En Optimizing the speaker setting for your listening roomUsing Auto Setup 25 En Number of speakers SP 26 EnSpeaker distance Dist Speaker level LVLPress 8n and then press 8l / h to select SET or Cancel If an error screen appears27 En If Warning appearsSelecting the desired Scene template Selecting the Scene templates28 En Selected Scene template is assigned to the buttonVideo games AUX Game Playing 29 EnWhich Scene template would you like to select? 30 En Preset Scene templates descriptionsCreating your original Scene templates Customizing the preset Scene Templates31 En Renaming the Scene templates32 En Using remote control on the Scene featureControlling the input source Components in the Scene mode Playback Quick guide to contentsBasic operations 33 En34 En Selecting audio input jacksSelecting the Multi CH Input component Muting the audio output Using your headphones35 En Current status screen appears in the OSD36 En Displaying the input source informationAudio information Video information37 En Using the sleep timer38 En Sound field programsSound field program descriptions 39 En Enjoying 2-channel sources using Standard decodersEnjoying unprocessed input sources Straight decoding mode Editing sound fields parameters 40 EnAdjusting the tonal quality Using audio featuresAdjusting the speaker level Enjoying high quality sound42 En Selecting the night listening modeAutomatic tuning Manual tuning FM/AM tuning43 En Lights up44 En Automatic preset tuningManual preset tuning Exchanging preset station Selecting preset stationsSee Selecting preset stations on this Press and hold BPRESET/TUNING for more than 3 seconds46 En XM Satellite Radio tuningXM Satellite Radio online information XM Ready legal disclaimer47 En Activating XM Satellite RadioBasic XM Satellite Radio operations Category Search mode All Channel Search modePreset Search mode Direct Number Access mode49 En Setting XM Satellite Radio preset channelsPreset channel number appears in the front panel display Displaying the XM Satellite Radio information in the OSD Displaying the XM Satellite Radio information50 En Connecting the SiriusConnect tuner Sirius Satellite Radio tuning51 En Sirius Satellite Radio legal disclaimerBasic Sirius Satellite Radio operations Activating Sirius Satellite Radio subscription52 En Displaying the Sirius ID of your SiriusConnect tuner53 En PRESET/TUNING/CH l/ h or 8PRESET/CH k/ nPRESET/TUNING/CH l/ hor 8PRESET/CH k/ n Setting the code number and the locked Channels Setting the Parental LockPRESET/TUNING/CH l/ h or 8PRESET/CH k/ n 54 En55 En Tuning into the locked channelsPress 8ENTER Press 8ENTER to confirm the code numberPress H Info or Odisplay 56 EnALL PopRemote control operation Using iPodControlling iPod in the simple remote Mode Controlling iPodFunction of the play information display Controlling iPod in the menu browse Mode58 En Pairing by using SET Menu Using Bluetooth componentsQuick pairing 59 En60 En Recording61 En Auto setup Auto SetupManual setup Manual Setup 62 En Using SET MenuSignal information Signal Info 63 En Speaker settings Aspeaker SET64 En Speaker level BSP Level 65 EnSpeaker distance CSP Distance Unit Unit66 En Audio settings Gaudio SETCenter speaker equalizer Dcenter GEQ Low-frequency effect level Elfe LevelInitial volume INIT.VOL Maximum volume MAX VOL67 En Support audio S.AUDIOInput assignment 68 EnFor Coaxial Input jack For Optical Input jacks 2DTS decoder prioritize setting Multi channel input setupDecoder select mode 69 En70 En Display settings Adisplay SETPress 8ENTER to start pairing Bluetooth setting Ebluetooth SETPress 9RETURN to exit from Start Pairing 71 EnSirius Satellite Radio setting XM Radio setting FXM Radio SET A. and Canada models only72 En XM Radio antenna XM AntennaControlling this unit, a TV, or other components Remote control features73 En Controlling this unitControlling other components 74 EnRemote control code default settings Setting remote control codesInput Component Manufacturer Default 75 En76 En Advanced setupSpeaker impedance SP IMP A. and Canada models only Only a STANDBY/ON, L Program l/ h,Initializing Init 77 EnTuner frequency step TU Asia and General models only Problem Cause Remedy See Troubleshooting78 En General79 En Problem Cause Remedy80 En Tuner 81 EnXM Satellite Radio 82 EnSirius Satellite Radio 83 En84 En Before Auto SetupDuring Auto Setup 1OUT of Phase After Auto Setup3LEVEL Error 85 En86 En BluetoothResetting the system Remote controlAdvanced setup menu appears in the front panel display 87 En88 En GlossaryLFE 0.1 channel 89 EnNeural Surround PCM Linear PCM90 En SpecificationsIndex Symbols91 En NumericsFdynamic Range 92 En93 En Selection, Preset stationFront panel Power Sirius Mute MD/CD-R Tuner DVD DTV/CBL DVR Iii List of remote control codesCCE NEI TV/DVD STS Front panel/Face avant HTR-6140Remote control/Boîtier de télécommande

HTR-6140 specifications

The Yamaha HTR-6140 is a versatile AV receiver that combines advanced audio technology with user-friendly features, making it an ideal choice for home theater enthusiasts. This robust receiver is designed to deliver high-quality sound and a rich cinematic experience, whether you are watching movies, playing video games, or enjoying your favorite music.

One of the main features of the HTR-6140 is its impressive power output, providing 610 watts across all channels. With a 7.1-channel configuration, it supports surround sound formats like Dolby Digital and DTS, allowing for an immersive audio experience that brings your media to life. The receiver also supports high-resolution audio formats, ensuring that every nuance in your favorite tracks is captured with clarity.

The HTR-6140 is equipped with Yamaha's unique YPAO (Yamaha Parametric Room Acoustic Optimizer) technology. This automated calibration system analyzes your room's acoustics and adjusts the receiver's settings accordingly. This ensures that you get optimal sound performance tailored to your specific environment, enhancing the overall listening experience.

Connectivity is another strong suit of the HTR-6140. With multiple HDMI inputs and outputs, you can easily connect all your devices, including Blu-ray players, gaming consoles, and streaming devices. It also supports 4K video pass-through, allowing for high-definition video playback without any loss in quality. Additionally, the receiver features legacy inputs like optical and coaxial, ensuring compatibility with older devices.

Yamaha's proprietary CINEMA DSP technology is integrated into the HTR-6140, offering a wide range of soundfield programs that recreate the atmosphere of famous concert halls and movie theaters. This technology enhances the spatial quality of sound, making it feel as though you are a part of the action on screen.

In terms of usability, the HTR-6140 includes a user-friendly on-screen menu and remote control. Its intuitive interface makes setup straightforward, allowing users of all skill levels to take full advantage of its capabilities. Furthermore, the receiver supports multiple audio zones, enabling you to enjoy music in different rooms simultaneously.

Overall, the Yamaha HTR-6140 is a powerful and feature-rich AV receiver that provides a wealth of options for audio and video enthusiasts. With its robust performance, advanced technologies, and ease of use, it stands out as an excellent choice for building a high-quality home theater system. Whether you're a movie buff, gamer, or music lover, the HTR-6140 offers a compelling audio experience that enhances every moment.