AudioSource AMP310, AMP210 owner manual 10 11 12 13

Page 4

AMP210 / AMP310

OWNER’S MANUAL

Speakers

AB

2

AMP210

Stereo Power Amplifier

 

Power

Signal / Clip

Signal / Clip

Left

Right

5 1 5

Balance Trim

Volume Trim

Left

Right

-12dB

+6dB

34

FRONT PANEL CONTROLS

1. Power

The front panel power switch switches the AMP210/310 on or off. Red LEDs behind the faceplate indicate power status. Whenever the amplifier’s

power switch is in the “ON” position the ring around the button is illuminated. When the amp is “Active” (receiving signal) the side lenses become illuminated and the signal LEDs show green. During “Standby” status (no signal) the side lenses are not illuminated and the signal LEDs show orange.

2. Speaker Selector

Selects speaker set ( A or B )

Figure 1. Front Panel

3. Balance Trim

Fades speaker output between the Right and Left Channels

4. Volume Trim

Allows fine adjustment of amplifier volume. 5. Clip LEDs

Blinks red during signal clipping. Reduce volume slightly.

Shows solid red during protect mode. Check speaker wires for shorts or extreme low impedance (< 4 ohms).

Connect

7 Receiver

Here

Line 1

 

 

Line 2

 

 

 

 

 

 

 

 

VSpeaker IN

Line 1R L

IN

+

 

 

 

 

 

+

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 L

 

 

R

-

-

Serial Number:

 

8

V Line 2

IN OUT L

R

9

 

 

 

 

 

 

CAUTION

 

 

AVIS

 

 

 

 

 

 

 

 

Use Class 2 Wiring

 

 

 

 

RISK OF FIRE OR ELECTRIC SHOCK

AVIS: RISQUE DE CHOC ELECTRIQE

Minimum Impedance:

 

 

 

 

 

 

 

DO NOT OPEN

NE PAS OUVRIR CE CARTER

 

 

 

 

 

 

 

 

8 ohm Bridged

 

 

 

 

 

 

 

RESERVE AU PERSONNEL AUTORISE

 

 

 

 

 

CAUTION: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE

 

 

 

 

 

 

 

 

4 ohm Stereo

 

 

 

 

COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUALIFIED PERSONNEL.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE

19

Light Bar Display

 

 

 

 

COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO

 

 

 

 

QUALIFIED PERSONNEL.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Delay

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On Off

 

 

 

 

 

 

 

 

 

 

 

 

12V Trigger

 

Auto On

Time

Master Level

Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN - OUT

 

 

 

 

 

 

3 Sec 15 Sec

Min Max Min Max

Stereo Bridged

 

Trigger Normal

RL

10 11 12 13 14

-

-

 

Speaker A

 

 

MODEL AMP210

 

R

+

+

L

-

 

Custom Manufactured in China

 

 

 

 

 

 

 

 

 

 

 

 

115V~ 60Hz 700W

18

 

 

 

 

 

FUSE:T6.3AL 250V

 

 

 

 

 

230V~ 50Hz 700W

 

 

 

 

 

FUSE:T3.15AL 250V

 

+ Bridge

-

 

 

 

 

R

+

+

L

-

 

 

 

Speaker B

 

 

CAUTION: See User Manual Before

 

 

 

 

 

 

 

15

 

 

16

 

Replacing Fuse

 

 

 

 

17

 

 

 

 

 

 

 

Figure 2. Rear Panel

REAR PANEL CONTROLS

6. Line 1 Input

A switching input that can be used if a second source is desired and will take over when a signal is present and has at least a 5mV level. Whenever there is no signal at this input, or a signal with less than 5mV level, the amplifier switches back to the Line 2 or “primary” input.

7. Speaker Level Input Line Select

Switches the input of the speaker level input to Line 1 or Line 2. 8. Speaker Level Input

Can be used to connect a source with speaker level output instead of line level outputs. Use the Speaker Level Input Line Select to route the source to Line 1 or Line 2.

9. Line 2 Input/Output

The primary line level input and output for a single source connection. 10. Delay Time

Allows for a 3-15 second delay to be set and accommodate the source connected to the Line 1 input.

11. Master Level Controls

Provides independent adjustment of Left and Right channel maximum level.

12. Mode Select Switch

Switches the amplifier from Stereo mode to Bridged mode

13. 12V Trigger

Allows the AMP210/310 to be powered on by other electronics or to power on other electronics via a 3.5mm mini phone plug cable.

14. Power Mode

Sets the power on option of the AMP210/310. Set it to Normal for manual power on/off. Set to Auto-On for signal sensing. Set to Trigger if the 12V Trigger input is used.

15. Right Channel Speaker Output

Right channel terminals for speaker outputs A and B. 16. Left Channel Speaker Output

Left channel terminals for speaker outputs A and B. 17. Mains Power Inlet & Fuse Holder

Accepts IEC type line cord. A fuse located in integrated holder provides safety protection from fault conditions: replace fuse with one of same type and rating only.

18. Mains Voltage Selector

Voltage selection switch is preset to 115V (USA). For use in areas which require 230V contact your dealer. Fuse must be of type and rating marked on amplifier for use at local mains voltage.

19. Light Bar Display Control

Turns light bar display on front panel on or off. Does not control Signal/Clip LEDs or power button light ring.

4

13970 SW 72nd Ave. Portland, OR 97223 • 503.914.4688 • www.audiosource.net

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents AMP210 / AMP310 Explanation of Safety Symbols Risk of Electrical Shock Do not OpenTechnical Support 10 11 12 13 Master Level Controls RCA INPUT/OUTPUTSpeaker Level Input Mode Switch Mains Power INLET/FUSE15 & 16 Speaker Terminals Light BAR DisplayMono Setup Stereo SetupSetup for Multiple Source Instructions Importantes EN Matière DE Sécurité Garanties InternationalesContrôles DU Panneau Arrière Contrôles DU Panneau AvantContrôles Principaux DE Niveaut ENTRÉE/SORTIE RCA Mode Sélectionner InterrupteurEntrée DE Niveau DU HAUT-PARLEUR Configuration Stereo Configuration MonoConfiguration Pour Sources Multiples ApplicationsSI Usted Necesita Servicio Para SUS Productos Audiosource Garantía Limitada Para Electrónicos Estados UnidosGarantías Internacionales Controles DEL Panel Trasero Controles DEL Panel FrontalControles DE Nivel Maestro ENTRADA/SALIDA RCA Entrada DE Nivel DE ParlanteInterruptor Selector DE Modo 15 16 Salida DE Parlante DE Canal DERECHO/IZQUIERDOConfiguración Estéreo Configuración MonoConfiguración Para Fuentes Múltiples AplicacionesAMP210 Specifications

AMP210, AMP310 specifications

The AudioSource AMP210 and AMP310 are versatile, high-performance integrated amplifiers designed for both home and commercial audio applications. These amplifiers are known for their reliability, exceptional sound quality, and user-friendly features, making them popular choices for those seeking to enhance their audio systems.

The AMP210 is a compact yet powerful amplifier, delivering 100 watts per channel at 8 ohms and 150 watts per channel at 4 ohms. Its sleek design allows for easy placement in various environments, whether it be a home theater setup, a multi-room audio system, or a professional audio installation. The AMP310, on the other hand, provides even more power and flexibility with a remarkable 150 watts per channel at 8 ohms and 300 watts per channel at 4 ohms. This makes it ideal for driving larger speakers or handling demanding audio environments.

One of the main features of both models is their dual-zone capability, allowing users to effortlessly manage audio in two different areas or rooms. Each zone can be controlled independently, making these amplifiers perfect for those who desire customized listening experiences across various spaces. Additionally, both the AMP210 and AMP310 come with a bridgeable mode, providing the option to combine the outputs of two channels for increased power when needed.

In terms of connectivity, these amplifiers are equipped with multiple inputs, including RCA and balanced XLR connections, ensuring compatibility with a wide range of audio sources. The amplifiers also feature a built-in signal sensing technology, which automatically powers the unit on or off depending on the input signal. This not only conserves energy but also provides added convenience for users.

The AudioSource amplifiers utilize class AB amplification technology, known for its high efficiency and low distortion, resulting in clear and dynamic sound reproduction across the frequency spectrum. Users can expect enhanced bass response, detailed mid-range, and crisp highs, making these amplifiers suitable for various musical genres and audio content.

Overall, the AudioSource AMP210 and AMP310 are excellent choices for anyone looking to elevate their audio experience. With their combination of power, versatility, and advanced features, these amplifiers offer a practical solution for both casual listeners and audiophiles alike, ensuring an immersive and enjoyable listening experience.
Top Page Image Contents