Yamaha DVX-S100 owner manual Connecting the antennas, Connecting indoor FM antenna

Page 20

CONNECTIONS

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

■Connecting indoor FM antenna

Connect the included indoor FM antenna to the FM ANT terminal.

■Connecting the AM loop antenna

1Set up the AM loop antenna, then connect it.

Indoor FM antenna	AM loop antenna
(included)	(included)

FM ANT	GND – AM ANT
75ΩUNBAL.

Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

2Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.

Bare wire

Tab

3Release the tab. (The tab will return to its original position when you release your finger.)

Once connected, pull the wires gently to check that they are connected securely.

4Orient the AM loop antenna for the best reception.

y

•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

16

Image 20

Contents DVX-S100 Important Safety Instructions Explanation of Graphical SymbolsFCC Information for US customers only Example of Antenna GroundingWe Want You Listening For a Lifetime For Canadian CustomersContents Features About this manualChecking the Accessories Installing Batteries in the Remote ControlDVR-S100 NX-SW100 NX-S100S x4, NX-S100C, SW-S100STANDBY/ON Controls and FunctionsFront panel Introduction Input H/GRemote control AMP mode Code SETLevel TestApproximately 6 m 20 feet Using the remote controlHandling the remote control Front panel display left Front panel display right Before connecting components Adjusting speaker output levels P.20After connecting components Preparation StepsPreparation Speaker SetupSpeaker placement Installing the speakers Placing the center speakerMounting the front and rear speakers Placing the front and rear speakersHang the holes on the protruding screws Connections ComponentsTypes of video jacks Types of audio jacksConnection example For Audio componentFor Video Component For A/V componentConnecting the antennas Connecting indoor FM antennaConnecting the AM loop antenna Set up the AM loop antenna, then connect itConnecting the speakers RED WhiteGreen Gray BlueUsing commercially available speakers and speaker cables Exchanging the speaker cablesConnecting to an external Amplifier Connecting the AC power cordTurning on the power Memory back-upAdjusting Speaker Output Levels Using the test toneLeft Right Center Subwoofer SUR AMPBasic Playback Basic operationsEnhancing the bass tones To mute the soundInput modes and indications When you have finished using this unitSetting the sleep timer Feature of DSP programs UsingSelecting a sound field program Basic FunctionsProgram Features CINEMA-DSP for cinema sourcesTV Sports Mono MovieMeans the Matrix 6.1 decoder is on Using Basic FunctionsTable of Program Names for Each Input Format Selecting PRO Logic Playing Dolby Digital Surround EX or DTS ES softwareVirtual Cinema DSP While playing a 2-channel source Press AMP Press q/DTSDisplaying the information about input signal Normal Stereo ReproductionRecording Special considerations when recording DTS softwareTimer playback/recording Disc Information Types of disc that this unit can PlayPlaying a Disc This manual, the type of discs are indicated as belowMP3 playback Structure of the disc exampleStarting play from a selected chapter Repeat playRemote Control DVD Mode SetupPlay Mode SubtitlePlaying a Disc Basic operationTo stop playback After operationSkip To select a specific trackSearch PauseON-SCREEN Menu Operating menu barTo turn the screen off To change the menu bar positionLanguage Signal type/dataIcons for disc menu Play mode menu Icons for player menuDisplay menu Audio menuDigital picture mode Transfer ModeTo change the user mode Shuttle screenUsing Multiple Functions Using a disc’s menuEnhancing video quality U.S.A Canada models only Video CD’s playback control VCDAdjusting the screen position when using progressive output Save the adjusted positionTo play a track on a specific group A. and Canada modelsEnhancing audio quality Disc To play a bonus groupTo change pages Press a to stop play Press Group while pressing ShiftAudio tracks SubtitlesAngles To turn the icon offPress a to stop play Press Play Mode while pressing Shift Programmed playCase of DVD-Audio Press a to stop playTo cancel the programmed tracks To exit programming modeTo change or add to the program during programmed play To move up and down the pages on the program screenTo cancel random mode Random play DVD-AudioTo play from the marked point To clear a bookmarkProgram repeat Random-sequence repeatDVD-Video DVD-Audio/Video-CD/CDRepeat A-BDVD-A DVD-V VCD CD To cancel A-B repeatPress A-B while pressing Shift Setup Menu Operating the setup menuTo get out from the setup menu mode To go back to the previous screenDVD-A DVD-V Summary of settingsMenu groups Items Options Mpeg DVD-A DVD-V VCDLanguage selection and language code list Language code listOthers DVD-Video Mode DemoTo change settings Level 7 to If you have forgotten your passwordSetting method Level Ratings DVD-VSpeaker settings DVD-A DVD-V Output modeTo exit the speaker setting mode Difference SettingDifference Setting Speaker balanceTuning Automatic and manual tuningAutomatic tuning Manual tuningPresetting stations Automatically presetting stations for FM stationsManually presetting stations TuningTuning in to a preset station Press PRESET/BAND againRepeat steps 1 to 5 to store other stations SecondsSetting the manufacturer code Remote Control FeaturesYou can release Code SET after entering the code MD/CD-RTable of control buttons CD/MD recorder0, ≥10 CH +Adjusting the items on the SET AdjustmentsSET Menu List of SET Menu itemsSettings 1A Center center speaker mode1B Front front speaker mode 1C Rear LR rear speaker mode1D Bass LFE/bass out mode 1E F. Level front level modeSwfr BothSP DLY Time speaker delay Range dynamic rangeR Balance balance Front left and right speakers ControlInput Mode initial input SP/PRE OUT output source SettingsOptical Input jack Coaxial Input jackAdjusting the Level of the Effect Speakers Press j / i to adjust the speaker output levelFor 5ch Stereo LevelAdjusting the delay time Following table shows factory-set delay timeAdjusting the parameter settings for PRO Logic II Music Changing parameter settingsDimension PRO Logic II Music parameter descriptionsTroubleshooting Problem Cause Remedy ReferGeneral AppendixVolume level No sound fromCenter speaker Rear speakersProblem Cause Disc playbackRemedy Refer On the unit’s display This unit does notRemote control TunerGlossary Cinema DSPInterlace and progressive output Video signal Silent CinemaSpecifications List of MANUFACTURER’S Codes VCRCDR Kenwood Pioneer SharpV883340-1