Yamaha DVX-S100 owner manual Remedy Refer, On the unit’s display This unit does not

Page 74

TROUBLESHOOTING

Problem

Cause

 

 

No on-screen

 

display.

 

 

 

On-Screen Menu

 

Icons not displayed

 

or only partially

 

displayed on the

 

television.

 

 

 

There is a lot of

 

ghosting.

 

 

 

“No Play” appears

The disc that this unit cannot play is loaded.

on the unit’s display.

 

 

 

This unit does not

The disc is not placed properly.

recognize disc (“No

 

disc” appears on the

 

display, or the

 

display shows the

 

status when no disc

 

is loaded).

 

 

 

Remedy

Refer

 

to page

Go to Display on the SETUP menu, and select

49

“On” for “On-Screen Messages”.

 

Press the cursor buttons (u,d) while the

34

rightmost icon is highlighted to change the

 

menu bar position.

 

Use the on-screen menu icons to adjust the

37

picture quality.

 

 

 

 

 

 

Place the disc properly.

 

 

70

Image 74
Contents DVX-S100 Important Safety Instructions Explanation of Graphical SymbolsFCC Information for US customers only Example of Antenna GroundingWe Want You Listening For a Lifetime For Canadian CustomersContents Features About this manualDVR-S100 Checking the AccessoriesInstalling Batteries in the Remote Control NX-SW100 NX-S100S x4, NX-S100C, SW-S100STANDBY/ON Controls and FunctionsFront panel Introduction Input H/GLevel Remote control AMP modeCode SET TestApproximately 6 m 20 feet Using the remote controlHandling the remote control Front panel display left Front panel display right After connecting components Before connecting componentsAdjusting speaker output levels P.20 Preparation StepsPreparation Speaker SetupSpeaker placement Mounting the front and rear speakers Installing the speakersPlacing the center speaker Placing the front and rear speakersHang the holes on the protruding screws Types of video jacks ConnectionsComponents Types of audio jacksFor Video Component Connection exampleFor Audio component For A/V componentConnecting the AM loop antenna Connecting the antennasConnecting indoor FM antenna Set up the AM loop antenna, then connect itGreen Connecting the speakersRED White Gray BlueUsing commercially available speakers and speaker cables Exchanging the speaker cablesTurning on the power Connecting to an external AmplifierConnecting the AC power cord Memory back-upLeft Right Center Subwoofer SUR Adjusting Speaker Output LevelsUsing the test tone AMPEnhancing the bass tones Basic PlaybackBasic operations To mute the soundInput modes and indications When you have finished using this unitSetting the sleep timer Selecting a sound field program Feature of DSP programsUsing Basic FunctionsTV Sports Program FeaturesCINEMA-DSP for cinema sources Mono MovieMeans the Matrix 6.1 decoder is on Using Basic FunctionsTable of Program Names for Each Input Format Virtual Cinema DSP Selecting PRO LogicPlaying Dolby Digital Surround EX or DTS ES software While playing a 2-channel source Press AMP Press q/DTSDisplaying the information about input signal Normal Stereo ReproductionRecording Special considerations when recording DTS softwareTimer playback/recording Playing a Disc Disc InformationTypes of disc that this unit can Play This manual, the type of discs are indicated as belowStarting play from a selected chapter MP3 playbackStructure of the disc example Repeat playPlay Mode Remote Control DVD ModeSetup SubtitleTo stop playback Playing a DiscBasic operation After operationSearch SkipTo select a specific track PauseTo turn the screen off ON-SCREEN MenuOperating menu bar To change the menu bar positionLanguage Signal type/dataIcons for disc menu Display menu Play mode menuIcons for player menu Audio menuTo change the user mode Digital picture modeTransfer Mode Shuttle screenEnhancing video quality U.S.A Canada models only Using Multiple FunctionsUsing a disc’s menu Video CD’s playback control VCDTo play a track on a specific group Adjusting the screen position when using progressive outputSave the adjusted position A. and Canada modelsTo change pages Enhancing audio quality DiscTo play a bonus group Press a to stop play Press Group while pressing ShiftAngles Audio tracksSubtitles To turn the icon offCase of DVD-Audio Press a to stop play Press Play Mode while pressing ShiftProgrammed play Press a to stop playTo change or add to the program during programmed play To cancel the programmed tracksTo exit programming mode To move up and down the pages on the program screenTo play from the marked point To cancel random modeRandom play DVD-Audio To clear a bookmarkDVD-Video Program repeatRandom-sequence repeat DVD-Audio/Video-CD/CDRepeat A-BDVD-A DVD-V VCD CD To cancel A-B repeatPress A-B while pressing Shift To get out from the setup menu mode Setup MenuOperating the setup menu To go back to the previous screenDVD-A DVD-V Summary of settingsMenu groups Items Options Mpeg DVD-A DVD-V VCDOthers DVD-Video Mode Language selection and language code listLanguage code list DemoSetting method Level To change settings Level 7 toIf you have forgotten your password Ratings DVD-VSpeaker settings DVD-A DVD-V Output modeDifference Setting To exit the speaker setting modeDifference Setting Speaker balanceAutomatic tuning TuningAutomatic and manual tuning Manual tuningManually presetting stations Presetting stationsAutomatically presetting stations for FM stations TuningRepeat steps 1 to 5 to store other stations Tuning in to a preset stationPress PRESET/BAND again SecondsYou can release Code SET after entering the code Setting the manufacturer codeRemote Control Features MD/CD-R0, ≥10 Table of control buttonsCD/MD recorder CH +SET Menu Adjusting the items on the SETAdjustments List of SET Menu items1B Front front speaker mode Settings1A Center center speaker mode 1C Rear LR rear speaker modeSwfr 1D Bass LFE/bass out mode1E F. Level front level mode BothR Balance balance Front left and right speakers SP DLY Time speaker delayRange dynamic range ControlOptical Input jack Input Mode initial inputSP/PRE OUT output source Settings Coaxial Input jackFor 5ch Stereo Adjusting the Level of the Effect SpeakersPress j / i to adjust the speaker output level LevelAdjusting the delay time Following table shows factory-set delay timeDimension Adjusting the parameter settings for PRO Logic II MusicChanging parameter settings PRO Logic II Music parameter descriptionsGeneral TroubleshootingProblem Cause Remedy Refer AppendixCenter speaker Volume levelNo sound from Rear speakersProblem Cause Disc playbackRemedy Refer On the unit’s display This unit does notRemote control TunerGlossary Cinema DSPInterlace and progressive output Video signal Silent CinemaSpecifications List of MANUFACTURER’S Codes VCRCDR Kenwood Pioneer SharpV883340-1