Yamaha DVX-S100 owner manual Installing the speakers, Placing the center speaker

Page 16

SPEAKER SETUP

Installing the speakers

■Placing the center speaker

Place the speaker on TV whose top is flat or on the floor under the TV or inside the TV rack so that it is stabilized. When placing the speaker on top of the TV, to prevent the speaker from falling down, put the provided fasteners at four points on the bottom of the speaker and the top of the TV.

■Mounting the front and rear speakers

When mounting the front and rear speakers on a wall, use the holes on the speakers’ back panels.

1Put the provided pads at the four corners on the rear of the front and rear speakers to prevent the front and rear speakers from moving by vibrations.

Fastener

Peel off the	2 Fasten screws into a firm wall or wall
seal	2 Fasten screws into a firm wall or wall
	support as shown below.

Cautions

•Do not place the speaker on top of the TV whose area is smaller than the bottom area of the speaker. If placed, the speaker may drop out causing an injury to you.

•Do not place the speaker on top of the TV with an inclination.

•Do not touch the adhesive surface after peeling off the seal as this will weaken its adhesive strength.

•Thoroughly wipe clean the surface where the fastener is to be applied. Note that adhesive strength is weakened if the surface is dirty, oily or wet and that this may cause the center speaker to drop.

■Placing the front and rear speakers

When placing the front and rear speakers on a flat surface, attach the included non-skid pads to the corners on the bottom of the speakers as shown below. This prevents the speakers from sliding around.

Diam. 3.5 to 4 mm

Min. 20 mm

6 mm

Tapping screw (Available at the hardware store)

Non-skid pads

12

Image 16

Contents DVX-S100 Important Safety Instructions Explanation of Graphical SymbolsFCC Information for US customers only Example of Antenna GroundingWe Want You Listening For a Lifetime For Canadian CustomersContents Features About this manualChecking the Accessories Installing Batteries in the Remote ControlDVR-S100 NX-SW100 NX-S100S x4, NX-S100C, SW-S100Front panel Controls and FunctionsSTANDBY/ON Introduction Input H/GRemote control AMP mode Code SETLevel TestHandling the remote control Using the remote controlApproximately 6 m 20 feet Front panel display left Front panel display right Before connecting components Adjusting speaker output levels P.20After connecting components Preparation StepsSpeaker placement Speaker SetupPreparation Installing the speakers Placing the center speakerMounting the front and rear speakers Placing the front and rear speakersHang the holes on the protruding screws Connections ComponentsTypes of video jacks Types of audio jacksConnection example For Audio componentFor Video Component For A/V componentConnecting the antennas Connecting indoor FM antennaConnecting the AM loop antenna Set up the AM loop antenna, then connect itConnecting the speakers RED WhiteGreen Gray BlueUsing commercially available speakers and speaker cables Exchanging the speaker cablesConnecting to an external Amplifier Connecting the AC power cordTurning on the power Memory back-upAdjusting Speaker Output Levels Using the test toneLeft Right Center Subwoofer SUR AMPBasic Playback Basic operationsEnhancing the bass tones To mute the soundSetting the sleep timer When you have finished using this unitInput modes and indications Feature of DSP programs UsingSelecting a sound field program Basic FunctionsProgram Features CINEMA-DSP for cinema sourcesTV Sports Mono MovieTable of Program Names for Each Input Format Using Basic FunctionsMeans the Matrix 6.1 decoder is on Selecting PRO Logic Playing Dolby Digital Surround EX or DTS ES softwareVirtual Cinema DSP While playing a 2-channel source Press AMP Press q/DTSDisplaying the information about input signal Normal Stereo ReproductionTimer playback/recording Special considerations when recording DTS softwareRecording Disc Information Types of disc that this unit can PlayPlaying a Disc This manual, the type of discs are indicated as belowMP3 playback Structure of the disc exampleStarting play from a selected chapter Repeat playRemote Control DVD Mode SetupPlay Mode SubtitlePlaying a Disc Basic operationTo stop playback After operationSkip To select a specific trackSearch PauseON-SCREEN Menu Operating menu barTo turn the screen off To change the menu bar positionIcons for disc menu Signal type/dataLanguage Play mode menu Icons for player menuDisplay menu Audio menuDigital picture mode Transfer ModeTo change the user mode Shuttle screenUsing Multiple Functions Using a disc’s menuEnhancing video quality U.S.A Canada models only Video CD’s playback control VCDAdjusting the screen position when using progressive output Save the adjusted positionTo play a track on a specific group A. and Canada modelsEnhancing audio quality Disc To play a bonus groupTo change pages Press a to stop play Press Group while pressing ShiftAudio tracks SubtitlesAngles To turn the icon offPress a to stop play Press Play Mode while pressing Shift Programmed playCase of DVD-Audio Press a to stop playTo cancel the programmed tracks To exit programming modeTo change or add to the program during programmed play To move up and down the pages on the program screenTo cancel random mode Random play DVD-AudioTo play from the marked point To clear a bookmarkProgram repeat Random-sequence repeatDVD-Video DVD-Audio/Video-CD/CDPress A-B while pressing Shift To cancel A-B repeatRepeat A-BDVD-A DVD-V VCD CD Setup Menu Operating the setup menuTo get out from the setup menu mode To go back to the previous screenMenu groups Items Options Summary of settingsDVD-A DVD-V Mpeg DVD-A DVD-V VCDLanguage selection and language code list Language code listOthers DVD-Video Mode DemoTo change settings Level 7 to If you have forgotten your passwordSetting method Level Ratings DVD-VSpeaker settings DVD-A DVD-V Output modeTo exit the speaker setting mode Difference SettingDifference Setting Speaker balanceTuning Automatic and manual tuningAutomatic tuning Manual tuningPresetting stations Automatically presetting stations for FM stationsManually presetting stations TuningTuning in to a preset station Press PRESET/BAND againRepeat steps 1 to 5 to store other stations SecondsSetting the manufacturer code Remote Control FeaturesYou can release Code SET after entering the code MD/CD-RTable of control buttons CD/MD recorder0, ≥10 CH +Adjusting the items on the SET AdjustmentsSET Menu List of SET Menu itemsSettings 1A Center center speaker mode1B Front front speaker mode 1C Rear LR rear speaker mode1D Bass LFE/bass out mode 1E F. Level front level modeSwfr BothSP DLY Time speaker delay Range dynamic rangeR Balance balance Front left and right speakers ControlInput Mode initial input SP/PRE OUT output source SettingsOptical Input jack Coaxial Input jackAdjusting the Level of the Effect Speakers Press j / i to adjust the speaker output levelFor 5ch Stereo LevelAdjusting the delay time Following table shows factory-set delay timeAdjusting the parameter settings for PRO Logic II Music Changing parameter settingsDimension PRO Logic II Music parameter descriptionsTroubleshooting Problem Cause Remedy ReferGeneral AppendixVolume level No sound fromCenter speaker Rear speakersProblem Cause Disc playbackRemedy Refer On the unit’s display This unit does notRemote control TunerGlossary Cinema DSPInterlace and progressive output Video signal Silent CinemaSpecifications List of MANUFACTURER’S Codes VCRCDR Kenwood Pioneer SharpV883340-1