Installation

2.Grasping the top and bottom flanges of the rear closure panel as shown in Figure 12, the entire panel is pulled out diagonally from one side.

Figure 12. Pull rear closure panel out of wall sleeve

Step 2. Install drain kit in wall sleeve.

Step 4. Install wall sleeve in wall opening.

For condensate to drain properly inside the unit, the sleeve must be installed properly:

•level from right to left

•with a slight downward pitch from the indoor side to the outdoor side

Note: If equipment is 230/208 volt, verify the electrical receptacle is located within 52 inches of the sleeve’s right hand corner. Do not use an extension cord.

Note: For installation procedures, please refer to the Installation Guide that accompanied the accessory.

4.Slide the chassis into the wall sleeve until the chassis flanges contact the front edge of the wall sleeve. See Figure 14.

5.Secure the chassis to the wall sleeve using three screws on each side of the chassis to ensure a proper seal between the chassis and the wall sleeve . The screws are supplied in a plastic bag which is attached to the power cord. See Figure 15.

6.Verify the indoor and outdoor grilles are free of airflow obstructions.

7.Make the power supply connections as detailed in the next step.

Drain kits are available for indoor or outdoor installation to help condensate drain from either the right or left side of the wall sleeve externally, or from the bottom of the sleeve internally.

Note: For installation procedures, please refer to the Installation Guide that accompanied the accessory.

If you do not use the drain kit, condensate will drain out of the rear of the wall sleeve. The drain kit must be installed before the outdoor grille is installed.

Step 3. Install outdoor air grille in wall sleeve.

5.Install unit chassis in wall sleeve.

WARNING

Fire Hazard!

Do not use an extension cord with this unit. Doing so may cause a fire.

1.Attach the insulation strip to the upper rear of the wall sleeve. See Table 13. If using an extended wall sleeve, attach the insulation strip between the two baffles, touching the baffle surface facing towards the front.

Figure 14. Slide unit chassis into the wall sleeve

An outdoor air grille directs airflow for proper unit operation and to protect the outdoor coil. Install the grille before installing the chassis.

Outdoor air grille options are either a stamped grille or an architectural grille. When replacing an old chassis with an existing grille, please check with your HVAC representative to determine if the new chassis can be used with the old outdoor grille.

Front

11”

 

Rear

Bottom

Figure 15. Secure chassis to wall

 

 

sleeve

Using the wrong type outdoor grille can decrease cooling or heating capacity, increase energy usage, or shorten compressor life.

Note: For installation procedures, please refer to the Installation Guide that accompanied the accessory.

Figure 13. Insulation strip location

2.Remove the cabinet front from the chassis by pulling the bottom of the cabinet front away from the chassis until the retaining clips disengage.

3.If using a subbase, be sure the right-hand subbase cover is removed before installing the chassis in the wall sleeve.

Step 6. Install unit power supply.

Note: For installation procedures, please refer to the Installation Guide that accompanied the accessory.

PTAC-SVX01C-EN

13

Page 12 Page 14
Page 13
Image 13
Trane PTAC-SVX01C-EN manual Bottom, Install unit power supply
Page 12 Page 14

PTAC-SVX01C-EN specifications

The Trane PTAC-SVX01C-EN is a cutting-edge Packaged Terminal Air Conditioner (PTAC) designed to provide optimal temperature control, energy efficiency, and user comfort in a variety of settings, including hotels, apartments, and office buildings. This unit stands out with its robust features and advanced technologies, making it a reliable choice for meeting diverse heating and cooling needs.

At the heart of the Trane PTAC-SVX01C-EN is its innovative design, which combines powerful performance with quiet operation. This unit utilizes a high-efficiency compressor that ensures rapid cooling and heating, providing ideal comfort regardless of the external climate. With a capacity range suitable for smaller spaces, the PTAC delivers strong performance while maintaining energy efficiency, thus reducing operational costs over time.

One of the key characteristics of the PTAC-SVX01C-EN is its user-friendly interface. The intuitive controls allow users to effortlessly adjust temperature settings, fan speeds, and modes of operation, including cooling, heating, and fan only. This flexibility enhances user comfort while optimizing energy consumption. Additionally, the unit features a programmable timer, enabling users to schedule operation according to their specific needs, further conserving energy when spaces are unoccupied.

The unit's Quiet Operation Technology minimizes noise levels, making it an ideal choice for environments where peace and quiet are paramount. This feature is particularly beneficial in hospitality settings, where guests expect a tranquil atmosphere. The PTAC is engineered to provide ample airflow while minimizing sound, creating a pleasant indoor environment.

Another standout feature of the Trane PTAC-SVX01C-EN is its advanced air filtration system. The integrated filter effectively captures dust, allergens, and other airborne particles, promoting a cleaner and healthier living environment. This is particularly essential for individuals with allergy sensitivities or respiratory issues.

Durability is also a hallmark of the PTAC-SVX01C-EN. Built with high-quality materials, it is designed to withstand the demands of continuous operation while requiring minimal maintenance. The unit's sleek and compact design allows for easy installation in various locations, ensuring versatility without sacrificing performance.

In summary, the Trane PTAC-SVX01C-EN represents a perfect blend of efficiency, comfort, and innovative technology. Its user-friendly controls, quiet operation, and advanced air filtration make it a leading choice for those seeking reliable climate control solutions in residential and commercial spaces alike. Whether for heating or cooling, the Trane PTAC-SVX01C-EN is engineered to deliver exceptional performance and lasting dependability.
Top Page Image Contents