Maintenance

Resistance Test

1.With no power, remove the leads from the compressor terminals.

2.Touch the leads of an ohmmeter to terminals C-S, start windings and C-R, run winding.

If either winding does not test continuous, replace the compressor.

Voltmeter

15 amp fuse

Ammeter

Capacitor

Figure 25. Testing capacitor resistance

Testing capacitance

capacitance (MFD) = 2650 X amperage voltage

Note: Replace the capacitor if the value obtained is not within 10% of the rating printed on the capacitor.

Ground Test

WARNING

Live Electrical Components!

During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.

With no power and compressor leads removed:

Set an ohmmeter on its highest scale. Touch one lead to the compressor body (clean point of contact, as a good connection is a must) and the other probe to each compressor terminal in turn. If a reading is obtained, then compressor is grounded and must be replaced.

If the voltage, capacitor, overload and motor windings test fail to show the cause for failure:

Ohmeter Compressor top

Terminals

Outlet Accumulator

Figure 26. Compressor ground test

1.With no power, wire a test cord to line voltage (Line & N).

Note: The wire size of the test cord must equal the line size, and the fuses in the test line must be of the proper size and type.

2.Connect a good capacitor of the right MFD and voltage rating into the circuit as shown in Figure 40.

Figure 27. Test cord connections

3.Carefully apply line voltage.

a.If the compressor starts and continues run, the cause for failure is somewhere else in the system.

b.If the motor fails to start - replace. Since all single phase compressors are of the permanent split capacitor design the high and low side pressure must be approximately equal or the low torque compressor may not start.

Indoor Coil and Air

Thermistors

1.Remove the Indoor Coil Thermistor leads from the circuit board.

2.Check the resistance of the Indoor Coil Thermistor against the table on the next page. The leads of the ohm meter will need to contact the ends of the thermistors that connect to the board.

3.Replace the Indoor Coil Thermistor if it does not test as above.

Outdoor Coil and Air

Thermistors

1.Remove the outdoor coil thermistor leads from the circuit board.

2.Check the resistance of the outdoor coil thermistor against the table on the next page. The leads of the ohm meter will need to contact the ends of the thermistors that connect to the board.

3.Replace the outdoor coil thermistor if it does not test as above.

Heater Assembly with Power OFF to the Unit and Heater

1.Remove the heaters in question and visually inspect the element for broken condition. Refer to the disassembly procedures for information on disassembling the heater.

2.Test the thermal fuse (one time fuse). If open, replace the heater assembly.

PTAC-SVX01C-EN

37

Page 37
Image 37
Trane PTAC-SVX01C-EN manual Ground Test, Resistance Test, Indoor Coil and Air Thermistors, Outdoor Coil and Air Thermistors

PTAC-SVX01C-EN specifications

The Trane PTAC-SVX01C-EN is a cutting-edge Packaged Terminal Air Conditioner (PTAC) designed to provide optimal temperature control, energy efficiency, and user comfort in a variety of settings, including hotels, apartments, and office buildings. This unit stands out with its robust features and advanced technologies, making it a reliable choice for meeting diverse heating and cooling needs.

At the heart of the Trane PTAC-SVX01C-EN is its innovative design, which combines powerful performance with quiet operation. This unit utilizes a high-efficiency compressor that ensures rapid cooling and heating, providing ideal comfort regardless of the external climate. With a capacity range suitable for smaller spaces, the PTAC delivers strong performance while maintaining energy efficiency, thus reducing operational costs over time.

One of the key characteristics of the PTAC-SVX01C-EN is its user-friendly interface. The intuitive controls allow users to effortlessly adjust temperature settings, fan speeds, and modes of operation, including cooling, heating, and fan only. This flexibility enhances user comfort while optimizing energy consumption. Additionally, the unit features a programmable timer, enabling users to schedule operation according to their specific needs, further conserving energy when spaces are unoccupied.

The unit's Quiet Operation Technology minimizes noise levels, making it an ideal choice for environments where peace and quiet are paramount. This feature is particularly beneficial in hospitality settings, where guests expect a tranquil atmosphere. The PTAC is engineered to provide ample airflow while minimizing sound, creating a pleasant indoor environment.

Another standout feature of the Trane PTAC-SVX01C-EN is its advanced air filtration system. The integrated filter effectively captures dust, allergens, and other airborne particles, promoting a cleaner and healthier living environment. This is particularly essential for individuals with allergy sensitivities or respiratory issues.

Durability is also a hallmark of the PTAC-SVX01C-EN. Built with high-quality materials, it is designed to withstand the demands of continuous operation while requiring minimal maintenance. The unit's sleek and compact design allows for easy installation in various locations, ensuring versatility without sacrificing performance.

In summary, the Trane PTAC-SVX01C-EN represents a perfect blend of efficiency, comfort, and innovative technology. Its user-friendly controls, quiet operation, and advanced air filtration make it a leading choice for those seeking reliable climate control solutions in residential and commercial spaces alike. Whether for heating or cooling, the Trane PTAC-SVX01C-EN is engineered to deliver exceptional performance and lasting dependability.