Sharp VL-A10H operation manual Special Note for Users in the U.K, Blue Neutral Brown Live

Page 3

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used.

Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type.

DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

—The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.

—The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.

Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three- pin plug.

Before replacing the plug cover make sure that:

—If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.

—The cord grip is clamped over the sheath of the mains lead and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Your VIEWCAM is designed to record in SP mode only. It will not perform normal playback for programmes prerecorded in LP mode.

This VIEWCAM does not have a PCM recording or playback function. PCM recordings made using other VCRs or audio dubbing cannot be played back on this unit.

If you record on a tape on which PCM sound has already been recorded, the audio track of the new VIEWCAM recording may not come out if the tape is played back on a PCM-capable VCR. If this occurs, set the VCR’s audio monitor select switch to the “Standard” position.

NOTE:

The VIEWCAM’s LCD panel is a very high technology product with close to 90,000 thin-film transistors*, giving you fine picture detail. Occasionally, a pixel may appear on the screen as a fixed point of blue, green, red, or black. Please note that this does not affect your VIEWCAM’s performance.

*Specifications are subject to change without notice.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents VL-A10H Power supply Blue Neutral Brown Live Special Note for Users in the U.KDo not aim the lens at the sun Avoid shocks and droppingAvoid placing Cleaning LCD Monitor ScreenAC Adapter Iii Battery packCR2025 type Audio/video cable Lithium battery Remote control ×Soft case Tripod adapter For 180 recordingContents Gamma Brightness Compensation Useful FeaturesAdvanced Features ReferencesCassette compartment door p When the cassette compartment door is openPart Names Operation SummaryRemote sensor p Rear view35 p Camera ModeVCR Mode On-screen Display IndexQuick Reference Index Video cassette is defective and should be Inserting and Removing Battery PackInserting the Battery Pack Removing the Battery PackRecording and playback times Charging the Battery PackPowering the Viewcam from an AC Outlet Perform above, then take out the cassette Inserting and Removing a CassetteInserting a Cassette Removing a CassetteRemoving the Lithium Battery Installing the LithiumMemory Battery BatterySetting the Date and Time Changing to the 12-hour Time ModePress the SET button B LCD screen side Using the Hand Strap and the Lens CapAttaching the Shoulder Strap Attaching and Removing the Lens CapOpening the Sun Hood Using the Sun HoodAttaching the Sun Hood Closing the Sun HoodMaximum Continuous Recording and Actual Recording Times Easy Camera Recording with Full Auto ModeTo Turn the Power Off To Pause RecordingZooming Tips on Recording PositionsBasic Operations Camera Recording Remaining Battery Power Display Approx. remaining On-screen Recording time IndicatorRemaining Recording Time Display Yback Volume ControlPlayback Asic OperationsTurn on the Viewcam in VCR mode, and begin tape playback see Watching the Playback on aVideo Search StillBasic Operations Playback Display button Useful FeaturesOperations of the On-screen Controls Menu buttonPerform steps 4 to 6 above Desired settingPress the SET button B to select Press the or button C or D to select the desired menu itemPress the button to select Select Recording the Date and TimePress the or button to select Display Press the SET button B to select AUTO, ON, or OFFType of Fade Modes Selecting Fade ModeUsing Fade Mode Fade In and Fade OutTo cancel Fade mode Quick ReviewTo use fade out only Recording Standby mode, press Menu button until appears Quick Return Edit SearchPress the Gama EFF. button a again To cancel Gamma Brightness CompensationGamma Brightness Compensation To obtain a brighter pictureGain-up Cat’s Eye To cancel the gain-up functionTo return to normal picture Wide ScreenMacro Shots Removing the Lens HoodTo pause recording, press the REC Stop button B Self RecordingNormal Self Recording More Information on Self RecordingPress the Message button in Recording Standby mode Self-recording MessageTo turn off the self-recording message screen Setting the Viewcam to Full Auto Mode Features Program SearchUseful To turn off the tape counter Tape Counter FeatureUsing the Counter To reset the counter to zeroUsing the Counter Memory During playback, press the Menu Button until appearsPress the Play button D to view the desired scene Turning On the Remote Control Mode Using the Remote ControlOperating the Remote Control Installing the Batteries in the Remote ControlType of Digital Picture Effects To cancel the digital picture effectAdvanced Features Digital Picture EffectsSelect Scene Menu in above Type of Scene SettingsTo cancel the scene setting Scene Menu Program AESuperimposing a Title Top of the screen and the cursor will Changing the Preset TitlesPress the Reset button to display the title input screen Press the or ß button Q to selectManual Focus To cancel Manual Focus modeAuto/Manual Focus Auto FocusTo cancel White Balance Lock White Balance LockPress the White BAL. button. White BAL. returns to blue To cancel Manual Exposure mode Manual ExposurePerform steps 1 and 2 above, then press the Auto button B Type of Backlight Modes Picture/Backlight AdjustmentsPress the Menu button until Camera mode or VCR mode appears Press the Exit button to turn off the adjustment screenPress the Gama EFF. button again. Gamma disappears To cancel Gamma PlaybackGamma Playback Turning Off the LCD Monitor BacklightTo stop editing Setting Edit ModeEditing Cutting Unwanted SequencesTips on Good Lighting Useful InformationHints for Better Shooting LightingDirty Video Heads Dew FormationReplacing the Fluorescent Lamp Battery PackUsing Your Viewcam Abroad References Video Cassette TapesUse only tapes with the mark with this Watching the Demonstration Demonstration ModeCancelling Demo Mode Button and slide Power switch toPower Camera mode Symptom Possible cause Suggested solution Before Requesting ServiceVCR Viewcam Specifications0P06-M-G
Top Page Image Contents