Sharp VL-A10H operation manual Replacing the Fluorescent Lamp, Battery Pack

Page 57

Replacing the Fluorescent Lamp

This VIEWCAM uses a fluorescent lamp to backlight the LCD monitor. If the monitor becomes dark or difficult to view, the fluorescent lamp may need to be replaced. Contact the nearest SHARP service centre or your dealer for further advice.

Battery Pack

Battery pack consumption

Recording with many starts and stops, frequent zooming, and recording in low temperatures will shorten actual recording times. Accordingly, be sure to turn off the power when not recording. Use of an auxiliary battery pack is recommended to prevent undesirable interruptions in your recording.

Do not use an insufficiently charged or weak battery pack. Use of such battery packs may cause the power to automatically stop during VIEWCAM operation to protect both the battery pack and the unit.

Note:

This VIEWCAM uses a Ni-MH (nickel-metal hydride) type battery pack. Use only the SHARP BT-H22 or BT-H32 battery packs. They are designed specifically for use with this VIEWCAM.

Battery pack life

The battery pack has a limited service life. If the period of use becomes noticeably shorter with a normal charge, the battery pack is at the end of its service life. Replace it with a new battery pack.

Extending battery pack life

It is recommended that you use the battery pack until its charge is fully drained and the VIEWCAM is inoperable before recharging the pack.

Recharge the battery pack right before recording. A battery pack stored for an extended time will naturally wear down, resulting in decreased recording time.

Do not try to recharge a fully charged battery pack before it has been discharged, as this will cause deterioration of the battery’s capacity.

Store the battery pack in a dry, cool place.

How to use the battery pack cover

When storing a fully charged battery pack, put the cover on it so that the “CHARGE” mark printed on the label is seen through the window, as shown.

 

CHARGE

Battery

Window

pack

 

Label

Cover

 

When storing a battery pack that is not fully charged, put the cover upside down so that only the battery pack casing is seen through the window.

Caution:

For safety reasons, put the cover on the battery pack when it is not being used. If the metal parts of the battery pack come in contact with other metal items, there is a danger that a short circuit may occur.

Battery power is consumed even when the VIEWCAM’s power is turned off. If you are not going to use your VIEWCAM immediately, remove the battery pack (see page 8).

Temperature during charging

The Ni-MH (nickel-metal hydride) type BT-H22 and BT-H32 battery packs can be charged at a temperature of 15°C to 30°C.

References

50

Image 57
Contents VL-A10H Power supply Blue Neutral Brown Live Special Note for Users in the U.KDo not aim the lens at the sun Avoid shocks and droppingAvoid placing Cleaning LCD Monitor ScreenAC Adapter CR2025 type Audio/video cable Lithium battery Battery packRemote control × IiiSoft case Tripod adapter For 180 recordingContents Advanced Features Useful FeaturesReferences Gamma Brightness CompensationPart Names When the cassette compartment door is openOperation Summary Cassette compartment door pRemote sensor p Rear viewVCR Mode Camera ModeOn-screen Display Index 35 pQuick Reference Index Video cassette is defective and should be Inserting the Battery Pack Battery PackRemoving the Battery Pack Inserting and RemovingRecording and playback times Charging the Battery PackPowering the Viewcam from an AC Outlet Inserting a Cassette Inserting and Removing a CassetteRemoving a Cassette Perform above, then take out the cassetteMemory Battery Installing the LithiumBattery Removing the Lithium BatterySetting the Date and Time Changing to the 12-hour Time ModePress the SET button B Attaching the Shoulder Strap Using the Hand Strap and the Lens CapAttaching and Removing the Lens Cap LCD screen sideAttaching the Sun Hood Using the Sun HoodClosing the Sun Hood Opening the Sun HoodTo Turn the Power Off Easy Camera Recording with Full Auto ModeTo Pause Recording Maximum Continuous Recording and Actual Recording TimesZooming Tips on Recording PositionsBasic Operations Camera Recording Remaining Battery Power Display Approx. remaining On-screen Recording time IndicatorRemaining Recording Time Display Playback Volume ControlAsic Operations YbackTurn on the Viewcam in VCR mode, and begin tape playback see Watching the Playback on aVideo Search StillBasic Operations Playback Operations of the On-screen Controls Useful FeaturesMenu button Display buttonPress the SET button B to select Desired settingPress the or button C or D to select the desired menu item Perform steps 4 to 6 abovePress the or button to select Display Recording the Date and TimePress the SET button B to select AUTO, ON, or OFF Press the button to select SelectUsing Fade Mode Selecting Fade ModeFade In and Fade Out Type of Fade ModesTo cancel Fade mode Quick ReviewTo use fade out only Recording Standby mode, press Menu button until appears Quick Return Edit SearchGamma Brightness Compensation To cancel Gamma Brightness CompensationTo obtain a brighter picture Press the Gama EFF. button a againGain-up Cat’s Eye To cancel the gain-up functionMacro Shots Wide ScreenRemoving the Lens Hood To return to normal pictureNormal Self Recording Self RecordingMore Information on Self Recording To pause recording, press the REC Stop button BPress the Message button in Recording Standby mode Self-recording MessageTo turn off the self-recording message screen Setting the Viewcam to Full Auto Mode Features Program SearchUseful Using the Counter Tape Counter FeatureTo reset the counter to zero To turn off the tape counterUsing the Counter Memory During playback, press the Menu Button until appearsPress the Play button D to view the desired scene Operating the Remote Control Using the Remote ControlInstalling the Batteries in the Remote Control Turning On the Remote Control ModeAdvanced Features To cancel the digital picture effectDigital Picture Effects Type of Digital Picture EffectsTo cancel the scene setting Type of Scene SettingsScene Menu Program AE Select Scene Menu in aboveSuperimposing a Title Press the Reset button to display the title input screen Changing the Preset TitlesPress the or ß button Q to select Top of the screen and the cursor willAuto/Manual Focus To cancel Manual Focus modeAuto Focus Manual FocusTo cancel White Balance Lock White Balance LockPress the White BAL. button. White BAL. returns to blue To cancel Manual Exposure mode Manual ExposurePerform steps 1 and 2 above, then press the Auto button B Press the Menu button until Camera mode or VCR mode appears Picture/Backlight AdjustmentsPress the Exit button to turn off the adjustment screen Type of Backlight ModesGamma Playback To cancel Gamma PlaybackTurning Off the LCD Monitor Backlight Press the Gama EFF. button again. Gamma disappearsEditing Setting Edit ModeCutting Unwanted Sequences To stop editingHints for Better Shooting Useful InformationLighting Tips on Good LightingDirty Video Heads Dew FormationReplacing the Fluorescent Lamp Battery PackUsing Your Viewcam Abroad References Video Cassette TapesUse only tapes with the mark with this Cancelling Demo Mode Demonstration ModeButton and slide Power switch to Watching the DemonstrationPower Camera mode Symptom Possible cause Suggested solution Before Requesting ServiceVCR Viewcam Specifications0P06-M-G