Kodak HR 500 manual Limitations, Kodak Service Agreements

Page 8

Regulatory Information

Limitations

Warranty service is limited to areas within Kodak’s established marketing centers in the contiguous United States, the island of Oahu in Hawaii, and some areas of Alaska.

This warranty does not cover circumstances beyond Kodak’s control; it does not cover service or parts for any attachments, accessories, or alterations not marketed by Kodak, nor to correct problems resulting from their use.

Damage caused by failure to meet the electrical specification in this manual is not covered under the warranty to service agreement claim.

Kodak makes no other warranties, express, implied, or of merchantability, for this equipment.

Repair or replacement without charge is Kodak’s only obligation under this warranty. Kodak will not be responsible for any consequential or incidental damages resulting from the sale, use, or improper functioning of this equipment, even if loss or damage is caused by the negligence or the fault of Kodak.

Such damages, for which Kodak is not responsible, include, but are not limited to, loss of revenue or profit, downtime costs, loss of use of the equipment, cost of any substitute equipment, and facilities or services of claims of your customers for such damages.

This limitation of liability does not apply to claims for injury to persons or damage to property caused by the sole negligence or fault of Kodak or by persons under its direction or control.

Kodak Service Agreements

For information on Kodak service agreements:

In the United States: call Kodak’s Service Marketing Contract Administration and Billing Support at 1-800-645-6325.

Outside the United States: contact your local Kodak representative.

viii	August 2001

Image 8

Contents Kodak Professional HR 500 Film ScannerPage Unpacking Instructions for August Hot Surface Symbol Fuse Label Regulatory InformationElectrical Hazard Symbol Mechanical Hazard SymbolWarranty Information Warranty PeriodWarranty Repair Coverage How to Obtain ServiceKodak Service Agreements LimitationsContents Contents Using This Guide About This GuideAbout This Guide How the Scanner Works Introduction and OverviewProduct Description Features and Benefits Introduction and OverviewBefore You Begin Action or Condition Need to Calibrate? Focus?Rear View Equipment OverviewFront View Minimum Software Requirements Recommended Configuration of the Host ComputerMinimum Host Computer Hardware Requirements Film Sizes Film Holders Provided with the ScannerConnecting and Operating the Scanner Preparing the Host ComputerConnecting the Scanner Changing the AC Input Voltage Setting and the Fuses Fuse arrow Fuse in holder Close the AC input module Attaching the Cables Starting Up the Scanner System Placing the Empty Film Holder in the Film Holder GuidePowering up the Scanner and the Host Computer Setting the Magnification and Calibrating Scanner Setting the Scan ParametersOperating the Scanner Selecting the Negative or Positive Balancing FilterRed handle is in NEG position Inserting a Negative or Mounted Slide Scanner Preparing a Carded NegativePreparing an Uncarded Negative Preparing a Mounted SlidePlacing the Film Holder in the Scanner Scanning a Single Frame FocusingShutting Down the Scanner Connecting and Operating the Scanner Validating the Scanner Starting the SAM SoftwareValidating the Scanner Setting the Magnification Calibrating the Scanner Making a Test Scan Select Write image to fileMm double Autofocusing Scanning the Image Checking the ScanCleaning Procedures Maintaining the EquipmentCleaning the Lens Cleaning the Light Bar Replacement Procedures Replacing the LampLeads Replacing the Round Balance Filters Maintaining the Equipment Replacing the Square IR Filter Maintaining the Equipment Maintaining the Equipment Appendix a Using the Service and Assembly Module SAM Installing the Service and Assembly Module SAM Software Backing Up Scanner FilesUsing the Operations Controls Performing the Functions on the Mag/Focus Tab Setting the Magnification Performing an AutofocusUsing the Service and Assembly Module SAM Setting Image Processing Parameters Calibrating the ScannerUsing the Capture Tab Setting the Scan Area Scanning the Image DataUsing the Miscellaneous Tab Backing Up and Restoring Files Using the Service and Assembly Module SAM Recommended Accessories Appendix B Ordering Accessories and SuppliesAccessories Supplies Appendix C Scanner Specifications Site SpecificationsScanner Specifications Appendix D Using the Long Roll Accessory Installing the Software for the Long Roll Accessory Downloading the Software and Firmware fromUpgrading the Scanner’s Firmware Using the Long Roll Accessory Installing or Removing the Long Roll Accessory Overview of PartsPreparing the Scanner for the Long Roll Accessory Mounting screws Connector Guide pins Attaching the Long Roll Accessory to the Scanner Alignment block Dowel pin Long Roll Accessory Rear mounting Unlatching the Gate Actuator Latching and Unlatching the Gate ActuatorLatching the Gate Actuator Installing the Aperture Plate 120/220Removing the Long Roll Accessory from the Scanner Setting the Punch Reader Height for the Current Film Size Punch SensorsAdjusting the Core Locator Height on the Spindle Loading and Threading Film Threading the Film Install the film on the spindle Setting the Punch Reader Height Click Load Film Installing the Adjustment Tool 120/220Visually Checking the Punch Reader Height Adjusting the Punch Reader Height Appendix D-1 Calibrating the Sensor Offsets Preparing and Loading the FilmUsing the Long Roll Accessory SAM, select ViewFilm Controls Setting the Lens Magnification Set the Line Offset y to Set Pixel Summing to Locating the First Punched Frame Type -1 in the First Punch Number fieldUsing the Long Roll Accessory Checking the Alignment and Adjusting the Sensor Offsets Set Position Button Increments to 0.05 inches Using the Long Roll Accessory Using the Long Roll Accessory Appendix D-2 Determining and Setting the Trigger Points Recording the Highest Numbers on the LEDsDetermining the Left Trigger Point Determining the Right Trigger Point Setting the Trigger Points at the Scanner Appendix D-3 Maintenance Cleaning the Punch Readers Cleaning the Rollers On the Film Controls window, click Stop Appendix D-4 Initial Setup of Sensors Resetting the Sensors to the Factory ValuesProgramming the Sensors for the Long Roll Accessory Programming the Left SensorProgramming the Right Sensor Appendix D-5 Table of Scan Area Values Appendix D-6 Film Splicing and Editing Guidelines PunchingIndex NumericsIndex Index Index