Toshiba IK-53V instruction manual Rear Side, Enlarged

Page 5

Rear Side

4

2

ON

1

3

75Ω HD/VD

EXT INT

OFF

SHT

TRG

P.S

M.G

VIDEO OUT

MIN

MAX

DC IN/SYNC

 

M GAIN

 

 

4

Enlarged

5

1

 

 

 

O

 

 

2

 

 

 

N

 

 

 

3

 

 

1

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

1VIDEO OUT DC IN/SYNC plug (12-pin connector)

This receives +12 VDC, and sends a video signal from the camera. When a synchronizing signal generator is connected to this plug and an external synchronizing signal (HD/VD signal) is applied, the camera can be operated synchronously with the external signal.

275Ω terminal switch (Terminal of external synchronizing HD/VD input signal) Set this switch to OFF when not terminated. The factory setting is ON.

3HD/VD signal input/output selector switch

Set to INT to output the HD/VD signals from the camera, and EXT to input external HD/VD signals. The factory setting is EXT.

4MODE SELECT switch

1Shutter speed setting (MODE SELECT switch bit 1 to 4)

Set to the shutter speed suitable for the shooting conditions. For each setting position, refer to

P.8. The factory setting position is shutter OFF.

2Reset restart/External trigger mode setting (MODE SELECT switch bit 5 to 7)

For each setting position, refer to P. 9 to 14. The factory setting position is NORMAL.

3Trigger polarity setting (MODE SELECT switch bit 8) Selects the polarity of an externally inputted trigger.

OFF: Positive ON: Negative The factory setting position is OFF.

4Partial scanning mode setting (MODE SELECT switch bit 9)

Use Pin 9 (PART input) of the 12-pin connector on the rear panel. For the mode setting, refer to

P.6. The factory setting is OFF.

(PART input; H: 2 to 5V, L: 0 to 0.4V)

During partial scanning mode, 134 lines are output to the screen center (frame rate 180 fps).

5Gain selector switch setting (MODE SELECT switch bit 0)

This switch selects the modes OFF (fixed) or ON (manual). The factory setting is OFF (fixed).

5Manual gain (M GAIN) control knob

This adjusts the gain of a video signal when the gain mode is set to ON by the MODE SELECT switch bit 0 on step 5 . The factory setting is the fully counterclockwise position.

4

Image 5
Contents FCC Statement IK-53V/IK-52VContents General Top/Bottom/Front Side Camera Parts and FunctionsEnlarged Rear SideStandard Connection Connector Pin AssignmentsConnections Bit Pin 9 of the 12-pin connec Mode Tor on the rear panel SettingVideo Scanning Modes Partial Scanning OFF All pixels scanningPartial Scanning on When Partial Scanning Mode is onNormal Shutter Description of the Mode Select SwitchElectronic Shutter Long Term Exposure Reset RestartExternal Trigger Shutter Speed Setting External Trigger ModeVD OUT*3 Video Index Video Index Pulse Width Trigger SYNC-RESET Picture Output Timing External Sync Operation Pulse Trigger SYNC-RESET Picture Output TimingShutter mode HD input VD input HD Input Specifications HD/VD Output Amplitude SpecificationsVideo Index Output Specifications Trigger Pulse SpecificationsNormal mode External HD/VD Input Phase SpecificationsReset-restart/external trigger mode External VD falling edgeVertical Output Waveform Timing Chart Horizontal Output Waveform Timing ChartIK-52V Exterior ViewIK-53V Specifications Spectral Sensitivity Characteristics Representative Values