Toshiba IK-TF7C instruction manual Names and Functions

Page 7

4. NAMES AND FUNCTIONS

1 Prism faceplate

8DC IN 12V terminal

2DISP button

4MENU UP button

(AWB)

DISP

MENU DATA

DC IN 12V

PAGE

6DATA UP (AWB) button

7DATA DOWN button

5 MENU DOWN button

	3 PAGE button	9 DIGITAL terminal
[ Front ]	[ Rear ]
1 Prism faceplate	The protection cap is attached on the lens mount portion. After removing the cap,
	mount the lens. Be careful not to scratch or touch the optical area.
2 DISP button	Used when switching the display.
3 PAGE button	Used when switching to the menu and when selecting the menus.
4 MENU UP button	Select the function to be confirmed or changed on the menu.
5 MENU DOWN button	Select the function to be confirmed or changed on the menu.
6 DATA UP (AWB) button	Changes the value of the function selected by the MENU (UP/DOWN) button.
	(Also used when using AWB.)
7 DATA DOWN button	Changes the value of the function selected by the MENU (UP/DOWN) button.
8 DC IN 12V terminal	Accept a DC power input (12V).
9 RGB terminal	8-bit RGB, digital signal, and sync signal are output in the Camera Link format.
	Trigger signal and external sync signal (HD,VD) are input.
	Mode switching signal for partial scanning is input.
	Accepts serial communication control signal.

7

Image 7

Contents Following information is only for EU-member states For Customer UseSafety Precautions Disclaimer Avoid setting in humid, smoky, vaporized or dusty places Table of Contents Components Available selections Preset value Items Controlled by Using on Screen DisplayNames and Functions Connection Connector Pin AssignmentsStandard Connection Result displayed Meaning OperationWhite Balance Automatic White Balance Manual White Balance OutlineOFF Shutter speed mode is E.TRG modeGain Shading CorrectionUsing the Menus Mode Setting by on Screen DisplayShutter Electronic shutter Changing each setting in Manu modePartial scanning setting MenusMode = SS Changing each setting in SS synchro. scan modeChanging the shutter speed setting Changing 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse settingMode = E.TRG E.TRG = 1P SR Changing each setting in 1P SR modeChanging 1P SR exposure time setting Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeChanging the gain in Manu mode Changing each setting in RR modeMode = E.TRG E.TRG = RR Changing each setting in GainWHT BAL White balance Changing R pedestal Changing the shading correction modeChanging the manual shading correction setting Changing master pedestalData UP, Down Menu UP, Down Adjusting horizontal phaseSync OptionExternal Sync Setting to factory setting statusExternal sync signal polarity Shutter mode HD input VD inputHorizontal phase adjustment Setting by the frameUsing the unit with external sync signal Setting by 1HFval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing EXT Trig External triggerGer, there will be an effect on the video 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPW SNR Pulse width trigger SYNC-NON Reset Trigger*1 About 1 ∝s 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETInput Timing Chart Example RR Reset restartLong Term Exposure Partial Scanning on When Partial Scanning Mode is onPartial Scanning Partial Scanning OFF All pixels scanningInput Output Signal Specificatoins Horizontal Output Waveform Timing Chart CCD Output Waveform Timing ChartVertical Output Waveform Timing Chart RGB, 3CCD SpecificationsBefore Making a Service Call External Appearance DiagramSymptom Items to be checked Step-by-step Procedures How to Obtain Warranty Service Limited One 1 Year Warranty of Labor and PartsImaging Systems Division