Toshiba IK - HD1C Connection on Back Panel Back panel view, 3A Connector Pin Assignments

Page 10

5 2 Caution on Connection

䊶Only use optional camera head model # IK-HD1H with this camera controller. The use of another head may cause damage to the control unit and camera head.

䊶When connecting the camera cables, be sure to turn off the camera control unit and any other equipment connected to it.

䊶For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved ungrounded type AC adaptor with the specifications described below.

Power supply voltage	䋺	12V DC	10%
Current rating	䋺 More than 830mA, Less than2.5A
Ripple voltage	䋺	Less than 50mV (p-p)
Connector	䋺 HR10A-7P-4S by HIROSE electronics Co. Ltd
		Pins 1, 2	䋺 12V
		Pins 3, 4	䋺 GND

䊶If the securing screw on the connector of the camera cable loosens, noise may appear on the screen. Be sure to tighten the connector completely.

5 3 Connection on Back Panel

Back panel view

14

2 3

1 2 3 4 5

6 7 8 9

5 3A Connector Pin Assignments

DC IN 12V

1+12V

2+12V

3GND

4 GND

REMOTE

1NC

2 TXD

3 RXD

4 NC

5 GND

6 NC

7 NC

8 NC

9 NC

10

Image 10

Contents IK-HD1C Safety Precautions Disclaimer Table of Contents Limitation of UsageOption Components Available selections Preset value Factory setting Items Controlled by the on Screen DisplayNames and Functions FrontConnection Standard Connection3A Connector Pin Assignments Connection on Back Panel Back panel viewAutomatic Black Balance OperationDisplay Meaning Features White BalanceAWB OK Scene File GainShading Correction Automatic shading correction operation finished correctlyMode Setting by the on Screen Display Using the MenusSHUTTER䋨Electronic shutter䋩 MenusFlicker may be large Changing the video level in the automatic shutter mode 䋨1䋮1䋩 Changing the setting in Auto modeChanging the automatic shutter response speed Changing the automatic shutter zone area Changing the shutter speed setting 䋨1䋮2䋩 Changing the setting in Manual mode䋨1䋮3䋩 Changing the setting in SS Synchro. Scan mode Changing the shutter speedGain Video gain Mode Auto MAX Gain䋨2䋮2䋩 Changing gain in Manual mode Modemanual䋨3䋩 WHT BALWhite Balance Changing color temperature settingConfirming the contents of the zone area selected by AWB Changing R PaintMode ATW Paint Changing the red gain 䋨3䋮3䋩 Changing gain in Manual modeMode Manual Gain Temp Changing the blue gain䋨4䋮1䋩 Changing gamma correction ON/OFF 䋨4䋩 Process䋨4䋮2䋩 Changing gamma correction level 䋨4䋮4䋩 Changing master pedestal 䋨4䋮3䋩 Changing detail outline gain䋨4䋮5䋩 Changing DNR Digital Noise Reduction 䋨5䋩 MATRIXMatrix color correction 䋨5䋮2䋩 Changing Matrix setting䋨5䋮1䋩 Changing Matrix color correction ON/OFF 䋨6䋩 Sync 䋨6䋮2䋩 Changing EXT. settingAdjusting horizontal phase 䋨6䋮1䋩 INT screen䋨7䋮3䋩 Changing manual shading correction mode 䋨7䋮1䋩 Changing Output mode䋨7䋮2䋩 Changing shading correction mode 䋨7䋩 OptionOutput RGB 䋨8䋩 Returning to factory settings䋨7䋮6䋩 Changing OSD Output mode RGB SyncSetting by 1H 䋨1䋩 External sync signal input conditionsUsing the unit with external sync signal External SyncBefore Making Service Call Symptom Items to be checkedSpecifications CCDExternal Appearance Diagram How to Obtain Warranty Service Step-By-Step Procedures One 1 Year Limited Warranty of Labor and PartsYour Responsibilities