Nikon SB-22 instruction manual Stby Standby Position, On Position, OFF Position

Page 33

SETTING POWER SWITCH ------------

m 06 1 1.5 3 ft 2 3 4 5 7 10

POWER FLA

UNCE OFF....ST,BY,.oN

• I

GN(lSO lOa) 25(m)/82(ft)

With other cameras:

Though the ON position is normally recommended for turning on the flash unit, ST8Y can also be used.

With other Nikon cameras, even if the camera 'sexpo- sure meter stays on , the S8-22 automatically turns off when not used for one or two minutes. To turn on again , set power switch to ON or OFF position , then reset to ST8Y. For convenience, you may also push the open-flash button to turn on the S8-22.

STBY (STANDBY) Position

Use to conserve energy and shorten recycling time.

With Nikon F·501/N2020, F·401/N4004, F·301l N2000, FA, FE2 and FG:

Use the S8-22'sST8Y position to turn on the S8 -22. In ST8Y position, when the camera'smeter turns off, in one or two minutes the S8-22 turns off automatically. To turn the S8 -22 on again, lightly press the camera's shutter release button.

Note: Wh en the Nikon FA or FE2 is connected to Nikon Motor Drive MD -12 via a remote cord, the camera 's meter stays on and the 58-22 remains on at STBY position.

ON Position

With cameras other than the Nikon F·501/N2020, F·401lN4004,F·301/N2000, FA, FE2 and FG :

This position is normally used to turn on the S8-22.

With the Nikon FA, FE2, and FG:

To turn on the S8-22 when using mechanical shutter settings (M250, M90 or 8), set power switch to ON.

OFF Position

When not using the flash unit, a/ways set the power switch to OFF position.

33

Image 33
Contents Nikon ===============CONTENTS================~ For Nikon F-401/N4004 camera users ~==FOREWORDI====Nomenclature Sync/multiple flash terminal Aperture index windows Basic Operation With Nikon F3·series cameras with DE·2 or \ ~----------------~9 Set lens to minimum Aperture largest f-number ~----------------~ Lightly press shutter release button and view \ .... --------.,.I\ ~ Set aperture Lightly press camera shutter release button Below Available wi th most Nikon cameras Setting Camera Shutter SpeedDetermining Aperture TTL Mode For TTL Automatic Flash Exposure Control32~~25 Set your chosen aperture ISO film speed Shooting distance range Usable apertures/shooting distance range in TTL modeExposure compensation in TTL mode ~Iign film speed in use with film speed Index A1 or A2 Mode for Non-TTL Automatic Flash Exposure Control~------------ ...\ Select appropriate apertureSet 58 ·22s mode selector to A1 or A2 according to Shooting distance range in A1 or A2 mode Align film speed in use With the film speed index Mode for Manual Flash Exposure ControlChoose aperture With Nikon F-401 / N4004, use camera saper- ture dial 32~~~25 4f11A With Nikon F·401/N4004, use camerasaper· ture dial Guide number at various film speeds Guide NumberStby Standby Position On PositionOFF Position READY-LIGHT Indications Ready-Ught Warning Functions Using WIDE-FLASH Adapter Manual exposure SYNCHRO-SUNLIGHT FILL-IN Flash PhotographyA1 or A2 Mode TTL ModeM Mode Diffusing the LlGHT Bounce Flash Photography Procedure Multiple Flash Exposures Using a DiffuserTTL Multiple Flash Photography Multiple Flash PhotographyMQJ~ System chart for TTL multiple flash operation~~,ctd.,se·,~ Manual Multiple Flash Photography Avoiding RED EYECLOSE-UP Flash Photography in TTL Mode 10C-+50C Tips on Speedlight CarePage About Batteries Sync Cords SC -11 and SC-15 TTL Remote Cord SC-17TTL Multi·Flash Adapter AS·10 TTL Multi·Flash Sync Cords SC-18 and SC-19 Flash Unit Couplers AS-4 and AS-7OC Unit SO·7 Angle of coverage SpecificationsDimensions TTL modeWeight Accessory providedPage Nikon