Tyco 8200-2646-00 B0 manual Installation and Operation Guide

Page 18

If the message "UPDATE NG RESET PLEASE" appears rather than "UPDATE OK RESET PLEASE", please write down the error messages shown on the screen and inform your technical support, while ignoring the following steps.

7.Power off the IP camera when this update process is finished, then remove the SD card from the IP camera.

8.Reconnect the Ethernet cable to the RJ-45 port as necessary.

9.Power ON the IP camera and it will work normally if the entire update procedure goes correctly.

10.Verify the version of the system software.

WARNING:

1.Don’t use the NTFS format in step 1.

2.Steps 1 to 3 have to be done on a PC.

3.Make sure the file of UPDATE.BIN is a correct one in step 3, or the IP camera will not work normally after being updated.

4.If the power of the IP camera is suddenly lost in step 6, please remove the SD card first and turn on the IP camera next to test its operation. If the IP camera remains working normally, please go back to step 3; otherwise, please inform your technical support.

5.In step 7, if the SD card is not removed and the IP camera does not get online as well, the updating process must be repeated again after rebooting the IP camera.

6.Make sure that the SD card is inserted in the correct position in step 4, or the IP camera will suffer permanent physical damage.

7.If the message "CSUM ERROR" appears immediately after step 6, it implies a problem in the file of UPDATE.BIN.

8.Don’t interrupt the process while the unit is updating itself; proceed with an SD card not including any system software of the unit, or else the unit will crash.

18

Installation and Operation Guide

Image 18
Contents Installation & Operation Guide Page Copyright Table Of Contents Operation Instructions for the Network Icrosoft I Nternet E XplorerSafety Precautions Product Features Product InstructionsProduct Features Technical SpecificationsSystem ImageGeneral I/O SupportedDimensions / Weight Accessories Included Description of the FRONT/REAR View Front Panel and Rear PanelDIP Switch Flank PanelRS485 pin D+ Alarm wiring diagram USB function Dhcp on Dhcp OFFBracket mount installation Installation Updating System Software File of the system firmware is intactInstallation and Operation Guide IP camera SD card Troubleshooting PC Wiring Configuration Cable ConnectionsConnect to a computer Connect to a LAN Hub Intranet Configure Your IP Camera Network Settings Enable Dhcp FunctionSet IP Address Installation and Operation Guide TCP/IP Communication Software TCP/IP Installation TCP/IP configuration settingSelect TCP/IP, and then click Properties Connection Testing Click Start → Programs → MS-DOS PromptType Camera IP address RJ-45 socket Connecting the IP camera Microsoft Internet ExplorerHomepage of Mjpeg mode Browsing images from the IP cameraChange Video Setting Video setting page of Mjpeg modeFocus Adjust function Exchange the image format 4200K, Outdoor 6500K, Push Hold Fine Tune mode White BalanceFrame rate Format 255Change the Network Setting Netmask Default GatewayDescription of function keys IP Address Http PortChange the Network Setting FTP Mjpeg mode only Smtp Server Change the Network Setting Smtp Mjpeg mode onlyDescription of function keys Account Name & Password Email AddressChange the Network Setting Sntp Description of function keys Sntp Server Time Zone SubmitChange the Network Setting Ddns Ddns Type Description of function keys Enable Ddns FunctionDdns Password Ddns Host NameChange the Network Setting PPPoE Ssdp Port Change the Network Setting -UPnPDescription of function keys UPnP PortChange the Network Setting IP Filter Change the Network Setting -Network Traffic Description of function keys Maximum Upload BandwidthDescription of function keys Local Time Change the System SettingSet the Date and Time of the system Set ManuallyTimestamp Color Change the System Setting TimestampDescription of function keys Enable Timestamp Timestamp LocationChange the System Setting Users Change the System Setting Digital I/O Change the System Setting Audio Change the System Setting RS485 Setting Change the System Setting Update Firmware View the Event Logs Description of function keys First Previous NextChange the Application Setting Alarm Memory BufferUpload Rates Max Mjpeg Numbers SD Card setting page of Mjpeg modeDescription of function keys Mjpeg Format Recording RateDescription of function keys File numbers Change the Application Setting -Language Setting Record setting page of Mjpeg mode Description of function keys Schedule Change the Application Setting -Record ScheduleChart Remove All SchedulesFTP Description of function keys Enable Alarm Trigger an AlarmAlarm Duration Predetermines the length of the alarm SmtpChange the Application Setting Alarm Motion Detection Change the SD card Setting Change the Pan/Tilt setting PPPoE & Ddns Using the PPPoE PPPoE SettingsDdns settings Test Go to the InternetBandwidth Calculator of the IP camera Advanced Operation QuestionSet the recording time the AVI duration of the SD card Use IE to view the recorded filesAdd a new user Set the PPPoE functionUse the Sub Hostname to view the IP camera Modify the userSpecifications Functions of client PC Appendix 1. -IP camera UPnP How To Check the IP class of your PCInstallation and Operation Guide Installation and Operation Guide Install UPnP Packets Installation and Operation Guide Turn on Services Installation and Operation Guide Installation and Operation Guide Installation and Operation Guide Scan LANCams through My Network Place Setting the IP Address ARP and ping from Windows or MS-DOSARP and ping from Unix or GNU/Linux Set up the Ddns Registering for a Ddns Create an accountInstallation and Operation Guide Address. It will renew the IP Address automatically Installation and Operation Guide Appendix 4. -MPEG4 Bit Rate Lookup Table of IP camera Unit is in Mbps/secondAppendix 5. -FAQ