Better Light 7 manual Appendix a, Cleaning the CCD Cover Glass

Page 84

Appendix A

Cleaning the CCD Cover Glass

First, position the camera insert face up on a clean, stable surface. Use the Clean/Park menu option to move the CCD to its cleaning position. The camera may remain turned on during the cleaning procedure.

We recommend the use of e-wipe™ cleaning pads for the best results with the least eﬀort.

1.Tear open the foil package. With- draw the e-wipe by holding one end only. Do not touch the other end of the pad. Do not unfold the pad. Work quickly after opening the package or the methanol in the pad will absorb water vapor from the air and leave

water spots when used.

2.Tuck the untouched end of the e-wipe under the insert opening at one end of the CCD. Lay your thumb sideways across the pad as shown.

3.In a single continuous motion, wipe the pad along the length of the CCD cover glass. Use the side of the thumb to apply very gentle pressure on the pad as the cover glass is wiped.

4.Using one continuous J-stroke motion, slide the pad side- ways oﬀ the CCD cover glass. The solvent residue evaporates cleanly almost immediately, do not dry the CCD glass. Do not re-use the e-wipe pad.

After inspecting the CCD cover glass for any remaining residue or dust particles, use the Park command to move the CCD back to its parked position.

e-wipe is a trademark of Photographic Solutions, Inc. (508/759-2322) www.photosol.com

84

Image 84

Contents Large Format Digital Scanning Camera System Revision D MarchAcknowledgements Page Page Contents Lock Crop Ratio Locking BothAudio Focusing Aid Multiple Color Focusing Altering Color Balance for Mood or EﬀectSaving a High Bit Depth Image Limit LineExporting Notes Automatically Opening the ImageHardware Setup Software Operation Line TimeLighting Parts List Connector Identiﬁcation Installing and Conﬁguring the ViewFinder Software Getting StartedMemory Requirements System RequirementsMacintosh PC PC version of the software is requiredQuick Start Guide Connect the camera insert to the control unitConnect the control unit to the host computer Mate the female end of the cable with the DBConnect the AC power to the control unit Install the viewing overlay on the camera’s ground glassTurn on the digital camera Turn on the host computerInstall the infrared blocking ﬁlter Mm thick Tungsten infrared blocking ﬁlterSelect the image capture settings Compose and focus the imagePut the insert into the camera Start the ViewFinder softwarePrescan Take the pictureTransfer the ﬁle to the computer View the ﬁnal imagePrescanning Making a PrescanFast Prescans Cropped Prescans Super View Prescans Canceling a Prescan Saving and Viewing PrescansColor Managed Prescans Rulers GuidesImage Capture Settings ResolutionPage Line Time ISO Capture Mode Exposure LockCanceling a Scan ScanningScanning to the Camera Disk Naming the Image Automatically Naming ImagesAdding Notes to Your Picture Exposure Evaluation Digital Spot MeteringRGB Data Values, EV Units Determining Relative Exposure Static Spot Meter Tool Setting the Spot Meter Size Histogram Judging Overall and Spot ExposuresStatic Spot Meter Location Readings Tool Bar Magnify ToolHand Tool Measure Tool Mac only Panorama ToolToneZones Tool Page Crop Mask Tool Grid ToolPage Tab Panels Size PanelScan Area & Cropping Size of the cropped area may still be adjusted while Diﬀerent unit. Example 15.24 cm x 10.16 cm at 300 pixels perLock Crop Ratio To set a speciﬁc shape for crop rectangle Clicking up or down buttons of Scan AreaLock File Size To specify an exact ﬁle size Faster Scans for Free Seconds Scan directionColor Panel Establishing Neutral Color BalanceSaving Color Balances Changing Existing Color Balances Deleting Color BalancesAltering Color Balance for Mood or Eﬀect Reverting to a Previous Color Balance Tagging Images with ICC ProﬁlesTone Panel Tone Curve SelectionsSaving a High Bit Depth Image Brightness/Contrast Tone Curve Adjustments Manual Tone Curve Adjustments Limit Line Spot Meter Reference PointsNegative Curves Bit Tone CurvesSetting the EV Scale Reference Tone Curve HistogramSelecting an Output Tone Scale Saving Tone Curves Deleting Tone CurvesFocus Panel Large Focus DisplaySelecting a Focus Site Reading the Focus Displays and Adjusting Focus Audio Focusing Aid Mac only Multiple Color FocusingInfrared Focus Image File Management and Retrieval ViewFinder File Manager Sorting Image Files Adding more Notes to Your PicturesExporting Notes Automatically Saving Files to a Folder Automatically Opening the ImageRetrieving Image Files Selecting the Retrieval Tone Curve USB controller only Deleting Image Files Hard Drive Storage CapacityMenus File MenuEdit Menu Display Menu Camera Menu Capture Mode Clean/ParkDiagnostics Opens the Clean/Park window to expose the CCD for cleaningUser Preferences Automatically Retrieving Images Saving FilesAfter highlighting the desired folder, click Right of the Save scan folder labelAutomatically Save Prescans Auto NamingAutomatic Scan Viewing in an Application Auto File Open Auto-rotate Retrieved Files MaskGrid GuidesUsing Sounds Baseline ISO SettingISO Increment Selection Pano Settings Use this feature, the factory settings are adequateTime Lapse CropCleaning the CCD Cover Glass Appendix aExposure Adjustments Appendix BManipulating Exposure Line TimeColor Balance Sensitivity Tone CurvesLens Aperture Lighting Line Time Settings Appendix CResolution Selections Appendix DModel 4000E-HS Model 6000-HS, 6000E-HSSuper 6K-HS Super 8K-HS Status Indicators PowerAppendix E StatusHardware Setup Appendix FPanoramic Adapter Scene PanoramaPage Rollout Panorama Object Panorama Hardware is assembled just as it is for a Rollout panoramaError Messages Camera reported error Not ReadyCamera reported error No Room Camera reported error Conversion ErrorCamera reported error Value Error Camera reported error Math ErrorScsi Errors Comm returned error Other Errors Unknown ErrorCamera Timed Out