Adcom GTP-860II manual ProLogic II Setup, Other Setup Functions

Page 26

The mode option sets the default surround mode to be used with each source. The options are DOLBY DIGITAL, DTS, PRO LOGIC II-C/M/P, HALL, STEREO, and 5 CH STEREO. The available choices in each of the fields can be selected with the left or right arrow buttons on the remote; confirm the choice with the select button.

3.6 ProLogic II Setup

Dolby ProLogic II is a surround mode that can be used to generate sur- round sound from stereo program material. The settings below can be

PROLOGIC II SETUP

CENTER WIDTH: 3

DIMENSION: 0

RETURN TO SETUP

used to optimize the surround sound listening experience when you are using ProLogic II.

DIMENSION = This parameter is used when listening in ProLogic II Music mode, it changes the level balance from front speakers to back speakers, much the same way the fader adjust works in some car audio systems. The value can be varied from -3 (more sound level from the rear)to 3(more sound level from the front).

CENTER WIDTH = This adjustment is used when listening to ProLogic II music mode. It changes the amount of sound coming out of the center speaker. Adjust this parameter for best over all imaging between the front left/right and center speaker. As the value in increased, the appa- rant image width of the sound stage

will increase.

3.7Other Setup Functions

The GTP-860 II also has certain func- tions that can be accessed by using multiple front panel buttons pressed simultaneously.

Reset 1: Restore factory default set- tings and NTSC video = FM/AM button + video 1 button

Reset 2: Restore factory default set- tings and Pal video = FM/AM button + video 2

Video Mode switch (system inter- change): Change unit between NTSC and Pal video = FM/AM button + CD button

Frequency interchange: Changes the unit AM stepping frequency between US (10kHz) and Europe (9kHz) = FM/ AM button + tape monitor button

VFD segment test: lights up all seg- ments of the front panel display = memory button + AM button + video 4 button. Press any key to exit test mode.

Display software version: shows cur- rent version of software on the front panel display = memory button + FM button + video 5 button. Press any key to exit.

Program EEPROM: Programs and restores the system memory to facto- ry preset condition = memory button

+CD button + surround mode button. Press any key when programming is complete.

26 ADCOM GTP-860 II Owner’s Manual

Page 25 Page 27
Image 26
Page 25 Page 27
Contents GTP-860II About Adcom Table of Contents Outdoor Antenna Grounding Placing the GTP-860II Key FeaturesSafety Information Unpacking the GTP-860IIDescription of Unit GTP-860II Front PanelInterface Overview Digital Tuner Controls To select a radio station that you have presetTo change a preset radio station To operate the tunerSurround Backs Volume KnobDisplay Window Input SelectorSurround modes are Surround ModeBass/Treble Controls GTP-860 II Rear Panel Preamp Outputs Component Video Inputs & Output25 RS232 Control dB Multi-Zone Source OutputsDigital Audio Inputs Connecting a Multi-Zone Source Right Left Digital input 75 ohmVolume Up/Down buttons GRC-800 Remote ControlMode button Play button Pause button 44 46 RDS button 46 47 AM button FM buttonGRC-800 Overview Remote FeaturesDynamic Range Source Selectors vidTuning Up/Down Volume Up/DownMode Button Stop ButtonSleep Button AM Button49 M1, M2, M3, M4 Macro Keys Selects Main Selects Video Remote Function TableEXT Programmable Stop CDFM PRE/TUNE RDS Tuning UP Tuning Down M1 Programming Your Adcom GRC-800 Remote For tuner functions changing stations, etcDeleting All The Programmed Macro CommandsProgramming Macro Initiator Buttons Function Suggested Speaker Locations On-Screen Display Operation & SetupSpeaker Config Channel Balance and Channel Test Delay ConfigInput Config ProLogic II Setup Other Setup FunctionsSymptom Troubleshooting ServicingWarranty Your ResponsibilitiesPage FM Tuner GTP-860II SpecificationsTone Controls L and R front only GeneralAdcom
Top Page Image Contents