Vivotek PZ7151, PZ7152 manual PPPoE Point-to-point over Ethernet

Page 31

VIVOTEK - A Leading Provider of Multimedia Communication Solutions

PPPoE (Point-to-point over Ethernet)

Select this option to conﬁgure your Network Camera to make it accessible from anywhere as long as there is an Internet connection. Note that to utilize this feature, it requires an account provided by your ISP.

Follow the steps below to acquire your Network Camera’s public IP address.

1.Set up the Network Camera in a LAN.

2.Go to Conﬁguration > Application > Server Settings (please refer to Server Settings on page 55) to add a new server -- email or FTP server.

3.Go to Conﬁguration > Application > Media Settings (please refer to Media Settings on page 53). Select System log so that you will receive a list of system log in TXT ﬁle format which contains the Network Camera’s public IP address in your email or on the FTP server.

4.Go to Conﬁguration > Network > Network Type. Select PPPoE and enter the user name and password provided by your ISP. Click Save to take effect.

5.The Network Camera starts to reboot.

6.Disconnect the power source of the Network Camera; remove it from the LAN environment to the Internet.

NOTE

►If the default ports are already used by other device connecting to the same router, the Network Camera will select other ports for the Network Camera.

►If UPnPTM is not supported by your router, you will see the following message.

►Steps to enable UPnPTM user interface on your computer:

Note that you must log on to the computer as a system administrator to install the UPnPTM components.

1.Go to Start, click Control Panel, and then click Add or Remove Programs.

User's Manual - 31

Image 31

Contents Page Table of Contents Read before use Package contentsRear panel Physical descriptionDI/DO Diagram Hardware Reset Hardware installation InstallationNetwork deployment Setup the Network Camera over the InternetInternet connection with static IP When using a PoE-enabled switch ADSL/Cable/Hub Software installation Using web browsers Accessing the Network CameraPage Using Rtsp players MPEG-4 Using 3GPP-compatible mobile devicesUsing Vivotek recording software Main Host Name Mjpeg protocol and media options Page Client Settings MP4 Saving Options System SystemSystem Time DI and do Manage User Root PasswordSecurity Add UserCreate and Install Certiﬁcate Enable HttpsTo create a self-signed certificate Certificate Information Network Type NetworkPPPoE Point-to-point over Ethernet Page Http Two way audio HttpsFTP Rtsp Streaming Page Wireless LAN PZ7152 only Page Page Ddns Ddns Dynamic domain name serviceCustomSafe100 Allowed list / Denied list Access listDelete allowed list / Delete denied list Audio and video Video settingsGate 160945 2008/04/09 Page Page Audio settings Motion detection Percentage = 30% Camera control Preset PositionDwelling time sec Patrol selection Application Media SettingsSnapshot20080104100341 Server Settings Page Page Event Settings Page Recording Recording SettingsPage Remote Log System logCurrent Log View parameters Reboot MaintenanceRestore Upload / Export Daylight Saving Time Conﬁguration File CalibrateUpgrade Firmware Page Overview URL Commands of the Network CameraStyle convention Method GET/POST General CGI URL syntax and parametersSecurity level Get server parameter valuesSet server parameter values Page Available parameters on the server Timezoneindex 489 ~ Group dii0~ndi-1 Group security Group doi0~ndo-1Subgroup of network http Subgroup of network rtsp Subgroup of network httpsSubgroup of network pppoe Group ipfilter Group wirelessPage Quality and 5 is the best quality Group audioinc0~ n-1for n channel products Adjust saturation of image according to mode settings Group upnpportforwarding Group upnppresentationPage Page Group eventi0~2 Group serveri0~4 Group recordi0~1 Group mediai0~4Drive the digital output Query status of the digital output Query status of the digital inputAccount management Capture single snapshotSystem logs Upgrade ﬁrmwareMethod Post Post data Camera ControlSystem Information RecallMethod GET IP ﬁltering Preset LocationsOpen the network streamings Get SDP of StreamingsTechnical Speciﬁcations Approvals LED IndicatorPower Installation, Management, and MaintenanceTechnology License Notice Electromagnetic Compatibility EMC