Vivotek PZ7112 manual Electromagnetic Compatibility EMC, Liability

Page 126

VIVOTEK

Electromagnetic Compatibility (EMC)

FCC Statement

This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions.

■This device may not cause harmful interference, and

■This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partial installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■Reorient or relocate the receiving antenna.

■Increase the separation between the equipment and receiver.

■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

■Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables must be used in order to comply with emission limits.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

This device (PZ7112/PZ7122) complies with the essential requirements of the R&TTE Directive 1999/5/ EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC.

This device (PZ7112/PZ7122) is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.

This device (PZ7112/PZ7122) may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.

Liability

VIVOTEK Inc. cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. VIVOTEK Inc. makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for any particular purpose.

126 - User's Manual

Page 125 Page 126
Image 126
Page 125 Page 126
Contents IP Surveillance Table of Contents Package Contents Read Before UsePhysical Description Rear panelDI/DO Diagram Hardware Reset Installation Hardware InstallationSetup the Network Camera over the Internet Network DeploymentInternet connection with static IP When using a PoE-enabled switch Software Installation Accessing the Network Camera Using Web BrowsersVivotek Using Rtsp Players Using 3GPP-compatible Mobile Devices MPEG-4Using Vivotek Recording Software Main Configuration Area Vivotek Video Control Buttons Drop-down List of Preset Positions Client Settings MP4 Saving Options Configuration System SystemSystem Time DI and doManage Privilege Root PasswordSecurity Manage UserEnable Https Create and Install Certificate MethodHttps Hypertext Transfer Protocol over SSL Https Create self-signed certificate manually Vivotek Vivotek Network Network TypePPPoE Point-to-point over Ethernet Steps to enable the UPnPTM user interface on your computer Vivotek Enable IPv6 Http//20010c08250000020202d1fffe0465f4 Http Https Two way audioFTP Rtsp Streaming Vivotek Wireless LAN PZ7112/PZ7122 only Vivotek Vivotek Ddns Dynamic domain name service DdnsCustomSafe100 Access List General SettingsFilter Administrator IP address IP address 192.168.2.x will be bolckedVideo Settings Audio and VideoImage Settings CCD Adjustment Advanced Mode Video quality settings for stream 1 / stream 2 Advanced Mode Ntsc Audio Settings Follow the steps below to enable motion detection Motion DetectionPercentage = 30% Preset Locations Camera ControlPatrol Settings Digital Zoom Zoom Times DisplayReturn to Home Position while Idle Homepage Layout PreviewLogo Theme Options Vivotek Application Customized ScriptEvent Settings Trigger Event Schedule Vivotek Vivotek Server Settings Server TypeVivotek Vivotek Media Settings Media TypeTrigger Activation Format is Yyyymmdd Click to open the directory Format is HH 24r Recording Settings RecordingRecording Settings 20081120 20081121 20081122 System Log Remote LogCurrent Log View Parameters Restore MaintenanceReboot CalibrateExport / Upload Files Upgrade Firmware Reboot system now This connection will close URL Commands for the Network Camera AppendixGeneral CGI URL Syntax and Parameters Security LevelGet Server Parameter Values Set Server Parameter Values Parameter pairGroupname Available parameters on the server Valid Values DescriptionName Value Edinburgh, Lisbon, London Name Value Security Description Get/set Normalstate High Name Subgroup of network http Subgroup of network sip OPEN, Shared Denyi0~9end 0.0 ~ Denied ending IPv4 address for connection Qcif Name Value Security TZO Logemerg Font color Themecolorconfigfont Bit 8 = Invalidate bit 1 ~ Bit 2 = External or built-in zoom function 0built-in Audioextmic Boolean Parameter Value Enable or disable trigger digital output Enable or disable this server action Group mediai0~4 mediafreespace is used internally Bit0 LSB = serveri0 Drive the digital output Query Status of the Digital Input Di0=state\r\n Di1=state\r\n Di2=state\r\n Di3=state\r\nQuery Status of the Digital Output Capture Single SnapshotAccount Management QualityUpgrade Firmware System LogsCamera Control Preset Locations RecallSystem Information Http//servername/cgi-bin/sysinfo.cgiIP Filtering Get SDP of StreamsOpen the Network Stream Technical Specifications ．PZ7112 Ntsc CCD, WlanTechnology License Notice Electromagnetic Compatibility EMC Liability
Related manuals
Manual 118 pages 11.39 Kb
Top Page Image Contents