Arcam C30, P35, P1 Bi-wiring and bi-amping loudspeakers, Beforeyou Start, BI-AMPINGYOUR System

Page 13

Bi-wiring and bi-amping loudspeakers

BEFOREYOU START

WARNING: Do not make any connections to your amplifier while it is switched on or connected to the mains supply.

Before switching on please check all connections thoroughly, making sure bare wires or cables are not touching the amplifier in the wrong places (which could cause short circuits) and you have connected positive (+) to positive and negative () to negative.

Always ensure that the volume control on your amplifier is set to minimum before starting these procedures.

BI-WIRINGYOUR LOUDSPEAKERS

Bi-wiring improves the sound of your system because it divides the high and low frequency signal currents into separate speaker cables. This avoids signal distortions arising from the high and low frequency currents interacting with one another within a single cable, as in conventionally wired systems.

You will need:

Speakers – with four input terminals each: these will be marked HF (High Frequency) and LF (Low Frequency).

Loudspeaker cables – two pairs of cables per loudspeaker (which may be joined at the amplifier end if your amplifier has only one pair of output terminals per channel). Or, a suitably terminated cable set (a loom, probably prepared by your dealer and capable of being used for bi-wiring in one length).

How to bi-wire loudspeakers

1.Remove the terminal links on the rear of your loudspeakers

WARNING:This step is essential or damage to your amplifier may result which is not covered under warranty.

2.Connect the cables as shown in the diagram below, ensuring correct polarity at all times.

SP2

Arcam P35 power amplifier

SP2

+ R

+

L –

SP1

 

SP1

HF

Right

HF

Left

+

speaker

+

speaker

LF

 

LF

 

 

 

 

 

Recommended bi-wiring configuration

BI-AMPINGYOUR SYSTEM

The performance of your system can be further enhanced over that

English

 

achieved with bi-wiring, by extending the principle one stage further

 

to include separate amplification for the low and high frequency drive

 

units in each loudspeaker enclosure.

 

Connect the integrated amplifier to the high frequency (HF) terminals

 

and connect the power amplifier to the low frequency (LF) terminals.

 

You will need:

Speakers – with four input terminals each (as with bi-wiring): these will be marked HF (High Frequency) and LF (Low Frequency).

Four channels of amplification – for example two P35 stereo amplifiers or four P1 monoblock amplifiers.

Loudspeaker cables – two pairs of cables per loudspeaker or a suitably terminated cable set (a loom, probably prepared by your dealer and capable of being used for bi-amping in one length).

Interconnect cables – one pair of high quality interconnect cables.

How to set up a bi-amped system

1.Remove the terminal links on the rear of your loudspeakers.

WARNING:This step is essential or damage to your amplifier may result which is not covered under warranty.

2.Connect the cables as shown in the diagram below, ensuring correct polarity at all times.

3.Use the interconnect cables to connect the PRE OUT sockets of the C30 to the corresponding AUDIO IN sockets of the power amplifier. If using the P1 amplifier, it may be necessary to “daisy- chain” the interconnect cables. See page 11 for more details on doing this.

+

Arcam P35 power amplifier +

 

 

R

 

L

 

+

+

 

Right

HF

 

HF

Left

speaker

LF

LF

speaker

 

 

+

+

+

+

 

 

R

Arcam P35 power amplifier

L

 

 

 

 

 

Recommended bi-amping configuration

13

Image 13
Contents Vorverstärker C30 Vollverstärker P35 Vollverstärker P1 Important Safety Instructions Safety guidelinesSafety Compliance Contents Using this handbookConnectingto a Power Supply Installation C30 pre-amplifierPower Amplifier Connection Positioningthe UnitConnectingto Other Equipment Volume Control Settings Using your C30 pre-amplifierFront Panel Controls This routes the VCR signal to the Tape output Showing the volume level and you are ready to recordRecording TAPE-TO-TAPE Copying DubbingAdjusting Listening Settings Setting up your C30 pre-amplifierCustomising Amplifier Settings IntroductionCR-389 Remote Control Using the remote controlP35 Power Amplifier Rear Panel Installation P35 and P1 power amplifiersP1 Power Amplifier Rear Panel Remote Switching Connecting LoudspeakersUsing Bare Wire Ended Leads Using Spade TerminalsFault Indications Using your power amplifierSP1 and SP2 P35 only BI-WIRINGYOUR Loudspeakers Bi-wiring and bi-amping loudspeakersBeforeyou Start BI-AMPINGYOUR SystemPower amplifier input Nominal sensitivity 800mV Technical specificationsContinual Improvement Policy C30 P35Remote-control codes Guarantee Service informationON-LINE Registration English Conformité AUX Normes DE Sécurité Consignes de sécuritéConsignes DE Sécurité Utilisation de ce manuelAutres Langues Merci d’avoir acheté cet appareil Arcam de qualitéPositionnement DE L’APPAREIL Installation Préamplificateur C30Raccordement À UNE Alimentation Électrique Branchement SUR UN Autre Appareil Utilisation du préamplificateur C30 Commandes DU Panneau AvantRéglage DE LA Puissance Enregistrement DE Bande À Bande Reproduction EnregistrementRéglages D’ÉCOUTE Réglage du préamplificateur C30Personnalisation DES Réglages DE L’AMPLIFICATEUR Télécommande CR-389 La télécommandeAmplificateur DE Puissance P35 Panneau Arrière InstallationAmplificateurs de puissance P35 et P1Amplificateur DE Puissance P1 Panneau Arrière Mise Soustension ET Horstension À Distance Branchement DES HAUT-PARLEURSConnexion EN Guirlande EN Dénudant L’EXTRÉMITÉ DES FilsAmplificateur DE Puissance P35 Panneau Avant Utilisation de l’amplificateur de puissanceVoyants DE Panne Avant DE Commencer Bi-câblage et bi-amplification des haut-parleursBI-CÂBLAGE DES HAUT-PARLEURS Système À Double AmplificationPolitique D’AMÉLIORATION Continue Spécifications techniquesImpédance d’entrée 22 kΩ Gain 31,5 dB Tableau des commandes IR Garantie ServiceInscription EN Ligne Français Wichtige Sicherheitsanweisungen SicherheitsrichtlinienEinhaltungvon Sicherheitsbestimmungen Sicherheit Hinweise zum HandbuchAndere Sprachen Aufstellen DES Geräts Montage Der C30 VorverstärkerNetzanschluss Verbindung MIT DEM VollverstärkerDer C30 bietet folgende Anschlüsse Bedienelemente AN DER Frontblende Verwendung Ihres Vorverstärkers C30Lautstärkeregelung Kopieren VON Band ZU Band Dubbing AufnahmeRecord Aufnahme Einleitung Einstellen Ihres Vorverstärkers Typ C30Abhöreigenschaften Einstellen Verstärker EinstellenCR-389 Fernbedienung Verwendung der FernbedienungP1 Vollverstärker Rückseitige Blende MontageVollverstärker P35 und P1Optional drittes Kanalmodul Lautsprecher Anschliessen Anschluss AN Andere GeräteFernschaltung Dreikanaloption NUR P35Fehleranzeige Verwendung Ihres VollverstärkersSP1 UND SP2 NUR P35 Doppelteverkabelung Ihrer Lautsprecher SystemsKontinuierliche Verbesserung Technische SpezifikationenMitgeliefertes Zubehör Befehle zur Regelung der Lautsprecher Codes für die FernbedienungONLINE-REGISTRIERUNG KundendienstinformationNotizen Notizen Notizen Pembroke AVENUE, WATERBEACH, Cambridge CB5 9QR, England

C30, P35, P1, C30, P35 specifications

The Arcam C30 and P35 are a prestigious pair of components designed to deliver superior audio performance, tailored for audiophiles who appreciate the finer details in sound reproduction. These models exemplify Arcam's commitment to high-quality audio engineering, integrating advanced technologies that appeal to both music lovers and home theater enthusiasts alike.

The Arcam C30 is a high-performance stereo preamplifier that offers exceptional sound quality and extensive connectivity options. Designed with a focus on audio fidelity, the C30 incorporates high-grade components and thoughtful circuitry to minimize noise and distortion. Its analog and digital inputs allow seamless integration with various audio sources, providing versatility for any audio setup. The C30 features a user-friendly interface and a dedicated remote control, giving users effortless access to their audio settings. The unit is equipped with sophisticated digital-to-analog conversion technology, ensuring that music and movie soundtracks are rendered with clarity and precision.

On the other hand, the Arcam P35 is a powerful stereo power amplifier that complements the C30 perfectly. With its robust design and excellent build quality, the P35 is capable of delivering an impressive output, making it suitable for driving a wide range of speakers efficiently. It employs advanced Class G technology, which combines the benefits of Class A and Class AB amplification, providing both high efficiency and low distortion. This ensures that users experience dynamic sound across all frequencies, enriching their listening experience, whether they are playing music or enjoying a cinematic performance.

Another notable mention is the Arcam P1, a compact but powerful power amplifier, designed for those who require flexibility in their setup. The P1's compact size does not compromise its performance, as it embodies Arcam's signature sound quality, providing admirable power and clarity. Its energy-efficient design makes it an attractive choice for both stereo and multi-channel systems.

Together, the C30, P35, and P1 represent a cohesive audio setup that prioritizes sound quality, reliability, and user experience. The synergy between these components assures unparalleled performance, allowing listeners to experience their favorite music and films in stunning detail. With their state-of-the-art technologies and exceptional craftsmanship, these Arcam models stand out in the competitive realm of high-end audio, making them an excellent choice for audiophiles seeking to elevate their audio experience.