Jenn-Air W10349768A installation instructions Install Griddle, Electronic Ignition System

Page 13

Install Griddle

(on griddle models)

The griddle is factory installed.

1.Place drip tray in the well at the front of the griddle. Slide tray toward the back until it stops.

A

B

A. Griddle drip tray

B.Griddle

2.Clean griddle before using. Refer to the Use and Care Guide.

Electronic Ignition System

Install Burner Heads and Caps

Install the burner head, making sure the alignment pins are properly aligned with the burner base. Place burner cap (black) on top of the burner head.

20,000 Btu/h Ultra Power™ Dual-Flame

Burner

A

A. Incorrect

B. Correct

B

15,000 Btu/h Professional Burner

A

A. Incorrect

B. Correct

B

5,000 Btu/h Simmer/Melt Burner

A

A. Incorrect

B. Correct

B

Initial Lighting and Gas Flame Adjustments

Cooktop burners use electronic igniters in place of standing pilots. When the cooktop control knob is turned to any position, the system creates a spark to light the burner. This sparking continues until the flame is lit or the knob is turned to Off.

Check Operation of Cooktop Burners

Push in and turn each control knob to the “LITE” position.

The surface burners and grill flames should light within

4 seconds. The first time a burner is lit, it may take longer than 4 seconds to light because of air in the gas line.

After verifying the proper burner operation, turn the control knobs to OFF.

If burners do not light properly:

Turn cooktop control knob to the “OFF” position.

Check that the range is plugged in and the circuit breaker has not tripped or the fuse has not blown.

Check that the gas shutoff valves are set to the “open” position.

Check that burner caps are properly positioned on burner bases.

Repeat start-up. If a burner does not light at this point, contact your dealer or authorized service company for assistance.

Flame Height

The cooktop flame should be a steady blue flame approximately ¼" (0.64 cm) high.

Dual Flame Burner

A

B

A. Upper flame

B. Lower (simmer) flame

Single Flame Burner

To Adjust Flame Height:

1.Unplug range or disconnect power.

2.Remove burner grates.

3.Remove the control knobs.

4.Open the oven door and remove the 2 screws on each side of the range that hold the control console in place.

NOTE: Make sure to leave oven door open or the control console will not rest in the side brackets properly once it is detached.

13

Image 13
Contents Commercial Style Dual Fuel Convection Ranges Installation InstructionsYour safety and the safety of others are very important Range SafetyTools and Parts Installation RequirementsProduct Dimensions 30 76.2 cm models Mobile Home Additional Installation RequirementsMobile home installations require Location Requirements48 121.9 cm models 36 91.4 cm models Cabinet DimensionsIf connecting to a 3-wire system If connecting to a 4-wire systemElectrical Requirements U.S.A. Only Electrical ConnectionGas Supply Requirements Electrical Requirements Canada OnlyType of Gas Natural GasUnpack Range Gas Supply Pressure TestingGas Supply Line Gas Pressure RegulatorInstall Anti-Tip Bracket Install Optional BackguardMeasurement B Measurement C30 76.2 cm and 36 91.4 cm Models Electrical Connection U.S.A. OnlyWall Mounting 48 121.9 cm ModelsGround-link screw Ground link bent away from range Wire connection Power supply cordVerify Anti-Tip Bracket Location Make Gas ConnectionLevel Range Complete ConnectionElectronic Ignition System Install GriddleReinstall Kick Plate If you need Assistance or Service Complete InstallationGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator Gas Supply Pressure TestingTo Convert Surface Burners Burner orifice spudNatural Gas Conversion Complete InstallationSmall Burner A. Burner cap Strip Circuits Cooktop SchematicsBurner Cooktop SW4 SW5 SW6 Atlas Board HMI Keyboard LCD Wiring DiagramsAtlas Board HMI Keyboard LCD 48 121.9 cm Oven Schematic for Jdrp and Yjdrp ModelsVotre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreOutils et pièces Exigences D’INSTALLATIONDimensions du produit Modèles de 30 76,2 cm Exigences d’emplacementConversion pour utilisation en haute altitude Modèles de 36 91,4 cm Dimensions du placardSpécifications de lalimentation en gaz Spécifications de l’installation électriqueRemarque Dégagements minimums Canalisation de gaz Type de gazDétendeur Débit thermique des brûleurs AltitudeInstallation du dosseret facultatif Instructions D’INSTALLATIONInstallation de la bride antibasculement Déballage de la cuisinièreMesure C Raccordement au gazMontage au plancher Montage au murInstallation de la plaque à frire Vérification de lemplacement de la bride AntibasculementRéglage de laplomb de la cuisinière Système dallumage électroniqueAllumage initial et réglages des flammes de gaz Réglage de la taille des flammesSi les brûleurs ne sallument pas correctement Hauteur de flammeAchever linstallation Réinstallation du garde-piedsSi vous avez besoin d’assistance ou de service Contrôle du fonctionnement du/des foursConversion pour lalimentation au propane Conversions Pour Changement DE GAZConversion du détendeur Test de pressurisation de la canalisation de gazConversion des brûleurs de surface Achever l’installationGicleur de brûleur Conversion pour lalimentation au gaz naturel Schémas des circuits Table de cuisson à 4 brûleurs Schémas de la table de cuissonSchémas de câblage SMPS14VCC45WVentilaturde Refroidissmente ORVENTLATEUR~ DEDuloquet Lampeshalogènes

W10349768A specifications

The Jenn-Air W10349768A is a premium range hood designed to enhance the functionality and aesthetic appeal of modern kitchens. With a blend of advanced technology and elegant design, this model meets the needs of culinary enthusiasts and homeowners alike.

One of the key features of the W10349768A is its powerful ventilation system. Equipped with a robust motor, it offers multiple fan speeds to efficiently eliminate smoke, odors, and airborne grease created during cooking. Its high airflow capacity ensures that even the most intense cooking sessions leave your kitchen fresh and clean. This range hood is particularly effective in larger kitchen spaces, making it a versatile choice for various layouts.

The design of the W10349768A prioritizes aesthetics as much as functionality. The sleek stainless steel finish not only provides a modern look but is also easy to clean and maintain, ensuring that it remains a focal point in your kitchen for years to come. The unit's minimalist design integrates seamlessly with a wide range of kitchen styles while providing the durability expected from a Jenn-Air product.

In terms of technology, the W10349768A features advanced noise reduction capabilities. It operates at a lower decibel level compared to traditional range hoods, making it ideal for open-concept living spaces where noise can disrupt conversations or the enjoyment of family gatherings. This attention to noise levels reflects Jenn-Air’s commitment to creating a pleasant cooking environment.

The range hood also comes with convenient features like adjustable lighting. Equipped with high-quality LED lights, it provides ample illumination for the cooking surface below, enhancing visibility while also being energy-efficient. This allows home cooks to monitor their meals effortlessly and adds an inviting ambiance to the kitchen.

Another notable characteristic of the W10349768A is its easy-to-use controls. The intuitive interface allows users to adjust fan speeds and lighting with just a touch, making it accessible for everyone in the household. Additionally, the dishwasher-safe filters ensure that maintenance is straightforward, promoting hygiene and performance.

All of these features make the Jenn-Air W10349768A a top choice for those looking to blend performance with style in their kitchen. Its powerful ventilation, modern aesthetics, and user-friendly technology position it as an essential tool for any serious home chef. Whether you're sautéing, grilling, or baking, this range hood is designed to enhance your culinary experience while elevating the overall design of your kitchen space.