JVC TK-C1460B instruction manual Backfocus adjustment ring, Mounting bracket locking screws, Inch

Page 27

INTRODUCTION

Controls, Connectors and Indicators

SET	CAMERA
	CAMERA
AWC	SETUP	EXT TERM-OFF
AWC		EXT TERM-OFF
MENU		INT/GL
		DUPLEX
		RX TERM-OFF
		NOT USED

ON

LL SIMPLEX ON

VIDEO

IRIS

1

2

3

Lens mount
To attach the lens.
This is applicable to both C-mount lenses
and CS-mount lenses.
Backfocus adjustment ring
Adjusting the back focus during lens
installation.
When readjustment is required, loosen
the locking screw	3	by turning it
counterclockwise and turn the back focus
adjustment ring 2 .
After the adjustment, tighten the locking
screw 3 again.
[BF LOCK] Back focus locking screw
This serves to fix the back focus-adjusting
ring.

4

5

6

7

	Camera-mounting bracket
	The bracket has been attached on the
	bottom of the camera before shipment. It
	can also be attached on the top
	according to the circumstance.
	To re-attach the bracket use the threaded
	holes at the top, with the camera
	mounting bracket locking screws 7 .
	Camera-mounting screw hole (1/4
	inch)
	Use this hole when mounting
	the camera onto a fixer, pan/	MAX.
	tilt unit, and the like. (Use a	MAX.
	tilt unit, and the like. (Use a	7mm
	screw shorter than 7 mm.)
	Rotation-preventive hole
	Make use of this rotation-preventive hole
	to prevent any fall when mounting the
	camera. Always make sure that the
	camera is securely mounted.
	Camera mounting bracket fixing screws
	(⋅2: M2.6 ⋅ 6 mm)
	Be sure to use a 6 mm long screw.

DC

8	Cover	12	[SET/AWC] Set. Auto White Control
	The cover slides open when pushed to		Button
	the left.		SET:	Press this button to display a sub-
9	[VIDEO/DC] Iris Selector Switch			menu.
				( Page 23)
	This should be set according to the type
			AWC: If this button is kept pressed for
	of lens if an automatic iris control lens is
				more than 1 second, a one-push-
	used.
				auto-white-balance function works
	VIDEO: In case of lens with EE amp built-
				and sets the white balance. Once
		in.
				it is set, even if colour temperature
	DC:	In case of lens without EE amp
				changes, white balance does not
		built-in.
				change. It is also possible to make
	(VIDEO: At time of factory shipment)
				fine adjustments on the set white
10	[IRIS] Iris Terminal
				balance.
	This is	connected to an automatic iris
				( Page 22)
	control lens.

	( Page 15)
11	[MENU] Menu Button
	When pressed, a menu screen is brought
	up.
	( Page 23)

E-8

E-9

Image 27

Contents Colour Video Camera TK-C1460B Serious damage to the appliance Power-line surgesSafety Precautions Memo FeaturesOperating Precautions SenseControls, Connectors and Indicators OUT Y/C output connector INT/GL, LL Selector Switch forDUPLEX, Simplex Selector Switch Signal connection terminalsRM-P2580 System Setting the switches Setting on the Menu screen When connectingVideo ProceduresMounting the lens DC Iris Video IrisInstalling the ferrite core Control signal cables Genlock connection CONNECTION/INSTALLATION Mounting the camera Installation of cameraFall Prevention With a fixed-focus lens Lens adjustment Back focus adjustment Back focus adjustment Level adjustmentSet the cursor to a desired Auto white balance control adjustmentSub-menu using Button Press the Menu buttonAT a CL Eared Menu Setting The flow of menu screenALC Settings Screen Sync Adjust ScreenOFF PriorityBLC Initial value MotionVideo Adjust Screen OFF Double Camera Title Edit Reverse Mode HLI Mode ALM.TITLE SizeAlarm TerminalCommunication Screen Maintenance ScreenFactory Settings Screen Motion Detect ScreenManual Adjustment of White Balance BLC Editting ScreenScreen Camera Title Setting Set the B&W item to AUX Output of Black-White/Color switching signal Set the B&W Item to Auto Set the AUX Terminal Item toWhite spot compensation SpecificationsMass 640 ˝ Accessory Instructions Ferrite core Dimensions Unit mmColour Video Camera TK-C1480BTK-C1481B Important Safeguards Safety Precautions Closes involuntary can occur TK-C1481BEG Connect the power cableWhen a highly bright subject is shot Low level, a malfunction such asCamera-mounting screw hole 1/4 Backfocus adjustment ringCover slides open when pushed to Mounting bracket locking screwsTK-C1480BE Power cable TK-C1481BEGShould be the same as the number of the Video Switch on the power againThis is the connected example of the TK-C1480BE That the ID number is the correct number the numberAttached 4 pin plugs TK-C1480BE DC 12 V or 24 Power supplyConnections on the back TK-C1481BEG AC230VThis diagram shows the installed example Changing the lens mounting method or using Lens adjustmentChange mark ∗ AGC Mode OL UX MOD E Shutter ExDRSpeed This item sets the order in which the AGC and slow shutter Speed AGC Mode Lolux Mode Sense UPMode Select Screen Area Edit Functions and set values Initial valueEdit 1 screen Light meteringArea Push the SET button Repeat the above items 2 toPush the Menu button 835 ˝ Accessory Vp-p, 75 ΩTK-C1481BEG