JVC TK-C1460B instruction manual Controls, Connectors and Indicators

Page 5

INTRODUCTION

Controls, Connectors and Indicators

SET	CAMERA
	CAMERA
AWC	SETUP	EXT TERM-OFF
AWC		EXT TERM-OFF
MENU		INT/GL
		DUPLEX
		RX TERM-OFF
		NOT USED

ON

LL SIMPLEX ON

VIDEO

IRIS

1

2

3

Lens mount
To attach the lens.
This is applicable to both C-mount lenses
and CS-mount lenses.
Back focus adjustment ring
Adjusting the back focus during lens
installation.
When readjustment is required, loosen
the locking screw	3	by turning it
counterclockwise and turn the back focus
adjustment ring 2 .
After the adjustment, tighten the locking
screw 3 again.
[BF LOCK] Back focus locking screw
This serves to fix the back focus-adjusting
ring.

4

5

6

7

Camera-mounting bracket
The bracket has been attached on the
bottom of the camera before shipment. It
can also be attached on the top
according to the circumstance.
To re-attach the bracket use the threaded
holes at the top, with the camera
mounting bracket fixing screws	7 .
Camera-mounting screw
hole (1/4 inch)
Use this hole when mounting
Use this hole when mounting
the camera onto a fixer, pan/	MAX.
tilt unit, and the like. (Use a	7mm
tilt unit, and the like. (Use a
screw shorter than 7 mm.)
Rotation-preventive hole
Make use of this rotation-preventive hole
to prevent any fall when mounting the
camera. Always make sure that the
camera is securely mounted.
Camera mounting bracket fixing screws
(⋅2: M2.6 ⋅ 6 mm)
Be sure to use a 6 mm long screw.

DC

8	Cover	12	[SET/AWC] Set. Auto White Control
	The cover slides open when push to the		Button
	left.		SET:	Press this button to display a sub-
9	[VIDEO/DC] Iris Selector Switch			menu.
				( Page 23)
	This should be set according to the type
			AWC: If this button is kept pressed for
	of lens if an automatic iris control lens is
				more than 1 second, a one-push-
	used.
				auto-white-balance function works
	VIDEO: In case of lens with EE amp built-
				and sets the white balance. Once
		in.
				it is set, even if colour temperature
	DC:	In case of lens without EE amp
				changes, white balance does not
		built-in.
				change. It is also possible to make
	(VIDEO: At time of factory shipment)
				fine adjustments on the set white
10	[IRIS] Iris Terminal
				balance.
	This is	connected to an automatic iris
				( Page 22)
	control lens.

	( Page 15)
11	[MENU] Menu Button
	When pressed, a menu screen is brought
	up.
	( Page 23)

E-8

E-9

Image 5

Contents Colour Video Camera TK-C1460B Serious damage to the appliance Power-line surgesSafety Precautions Operating Precautions FeaturesSense MemoControls, Connectors and Indicators DUPLEX, Simplex Selector Switch INT/GL, LL Selector Switch forSignal connection terminals OUT Y/C output connector Setting on the Menu screen Setting the switchesWhen connecting RM-P2580 SystemMounting the lens ProceduresDC Iris Video Iris Video Genlock connection Installing the ferrite core Control signal cables Fall Prevention CONNECTION/INSTALLATION Mounting the cameraInstallation of camera Back focus adjustment Lens adjustment Back focus adjustmentLevel adjustment With a fixed-focus lensSub-menu using Button Auto white balance control adjustmentPress the Menu button Set the cursor to a desiredAT a CL Eared Menu Setting The flow of menu screenALC Settings Screen Sync Adjust ScreenBLC PriorityInitial value Motion OFFVideo Adjust Screen Alarm Camera Title Edit Reverse Mode HLI Mode ALM.TITLE SizeTerminal OFF DoubleFactory Settings Screen Maintenance ScreenMotion Detect Screen Communication ScreenScreen Manual Adjustment of White BalanceBLC Editting Screen Camera Title Setting Set the B&W Item to Auto Output of Black-White/Color switching signal Set the AUX Terminal Item to Set the B&W item to AUXMass 640 ˝ Accessory Instructions Ferrite core SpecificationsDimensions Unit mm White spot compensationColour Video Camera TK-C1480BTK-C1481B Important Safeguards Safety Precautions When a highly bright subject is shot TK-C1481BEG Connect the power cableLow level, a malfunction such as Closes involuntary can occurCover slides open when pushed to Backfocus adjustment ringMounting bracket locking screws Camera-mounting screw hole 1/4TK-C1480BE Power cable TK-C1481BEGThis is the connected example of the TK-C1480BE Switch on the power againThat the ID number is the correct number the number Should be the same as the number of the VideoAttached 4 pin plugs Connections on the back Power supplyTK-C1481BEG AC230V TK-C1480BE DC 12 V or 24This diagram shows the installed example Changing the lens mounting method or using Lens adjustmentChange mark ∗ AGC Mode OL UX MOD E Speed ShutterExDR This item sets the order in which the AGC and slow shutter Speed AGC Mode Lolux Mode Sense UPMode Select Screen Area Edit Functions and set values Initial valueArea Edit 1 screenLight metering Push the Menu button Push the SET buttonRepeat the above items 2 to TK-C1481BEG 835 ˝ AccessoryVp-p, 75 Ω