JVC TK-C1460B This is the connected example of the TK-C1480BE, Switch on the power again

CONNECTION/INSTALLATION

RM-P2580 System

System with up to 8 cameras

Connecting the control signal cable

(Use a twisted-pair cable for connection.  Page 17.)

Camera 1

MACHINE ID:1 (Menu screen) RX TERM: OFF (switch)

Camera TK-C1480B

Camera TK-C1480B

Control signal cable
Video signal cable
Power	AC24V
	or
cable
	DC12V

Camera 1
control signal
connection terminals
TX+ A
TX	B
RX+ C

RM-P2580
A RX	+
B RX	+
C TX

Connect: Camera TX+ to RM-P2580 RX+ Camera TX– to RM-P2580 RX– Camera RX+ to RM-P2580 TX+

Camera 2	AC24V
MACHINE ID:2
	or
(Menu screen)
	DC12V
RX TERM: OFF
(switch)
	Camera
	TK-C1480B

RX	D
Camera 2
control signal
connection terminals
TX+ A

D TX

Camera RX– to RM-P2580 TX– The A B C D marks indicated on both the camera terminals and the RM-P2580 termi- nals facilitate correct connections. Connect the terminals with identical marks.

Camera 8

MACHINE ID:8 (Menu screen) RX TERM: ON (switch)

AC24V	•	•	•	•	•	CAM SW	Time lapse VCR
or
						OUT	SR-L910
DC12V
							VIDEO IN

MONITOR

TX	B
RX+ C
RX	D

Setting the switches ( Page 10)

Remote Control Unit RM-P2580

TO CAMERA

TO CAMERA

- -

POWER

OFF

ACINPUT

			CAMERA
				SW		COM
			DATA I / O				SERIAL-1	SERIAL-2
1	2	3	4	5	6	7	8		MONITOR
				VIDEO INPUT
							MONITOR MONITOR		OUTPUT 2
							1	2
							OUTPUT OUTPUT
1	2	3	4	5	6	7	8
				VIDEO OUTPUT
								MONITOR
								OUTPUT 1

MONITOR

EXT TERM-OFF ON

INT/GLLL

DUPLEXSIMPLEX

RX TERM-OFF ON

Select the synchronization method of the camera image. Set the switch on all cameras to LL (Line Lock) and match with the V. PHASE. ( Page 26.)

Set this switch to the DUPLEX

* If the setting is changed, be absolutely sure to

switch on the power again.

This is the connected example of the TK-C1480BE.
When controlling with any system except the RM-P2580, execute proper settings using
switches and menu screens according to the systems used.	( Page 14)
MEMO

VIDEO

DC

IRIS

NOT USED

Set this switch to ON (signal termination ON) only on the camera placed at the end of the control signal cable. Set to OFF on all other cameras.

•When operating a system using the RM-P2580, several cameras (up to 8) can be con- nected and used on one control signal cable. Consequently, an incorrect switch setting on just a single camera will cause the entire system to work incorrectly.

•Confirm switch settings on the screen as follows.MONITOR screen

q Confirm that the image from the camera to be checked	(example showing camera ID as “05”)
is displayed on the monitor.

w Turn OFF and then ON the AC 24 V power to the cam-
era to be checked.
e The camera begins the initial operation and characters
similar to those shown in the illustration on the right
appear on the monitor screen.
r Confirm that “DUPLEX” and “ID-□□” are displayed and
that the ID number is the correct number (the number	P R O T O C O L : D U P L E X			I D - 0 5
should be the same as the number of the VIDEO IN-
PUT terminal to which the camera is connected on the
rear panel of the RM-P2580).	“DUPLEX”	should	The number shown in the
t If wrong, set the camera ID again.
	be displayed.		□ □ part of ID-□ □
			should be correct.
E-12

Setting on the MENU screen ( Page 33)

* If the setting is changed, escape from the menu screen once, and definitely switch on the power again.
C OMMUN I C A T I O N		Set to M.DROP
		Set to M.DROP when the RM-P2580 is used
S T YL E	M . DROP	as a remote control unit. When controlling
MACH I NE I D	1
		from another machine, make sure that it
		matches the communication system used.

MACHINE ID setting switches

Set this item to match the RM-P2580 VIDEO

INPUT terminal number for each camera.

When connecting

●Turn OFF the power supply to all equipment to be used before making connections.

●Carefully read the Instructions for each piece of equipment to be used before making connections.

●For the appropriate connection cables and the length of these, carefully read “Connections on the back” on page 16.

●The control signal cable cannot be used for loop connection.

E-13