JVC GZ-MG365 manual Troubleshooting, Following phenomena are not malfunctions, To reset the camera

Page 33

FURTHER INFORMATION

Troubleshooting

The camera is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly.

The following phenomena are not malfunctions.

•The camera heats up when it is used for a long time.

•The battery heats up during charging.

•When playing back a video fi le, the image stops momentarily or the sound is interrupted at junctions between scenes.

•To solve the problem, fi rst follow the instructions below.

•If the problem is not solved, reset the camera. ( below)

•If the problem persists, please consult your nearest JVC dealer.

LTo reset the camera

1)Close the LCD monitor to turn off the camera and remove the power supply (battery pack or AC adapter) from the camera, then reattach it.

2)Select [FACTORY PRESET] from the MENU.

ENGLISH

Power

Recording

Trouble

Action



 

• Connect the AC adapter securely.

14

 

No power is supplied.

• Detach the battery pack once again and reattach it fi rmly.

14

 

• Replace the dead battery with a fully charged one.

–

The power does not

• Make sure to use the camera under appropriate operating

36

turn on, or the battery

temperatures.

 

operation time is

• The battery is worn out and needs to be replaced. Please

–

extremely short even

purchase a new one.

 

after the battery is fully

 

 

charged.

 

 

 

 

 

The access/charge

• Charging may stop in places subject to extremely high/low

–

temperatures to protect the battery. It is recommended

 

lamp on the camera

to charge it in places with a temperature of 10°C to 35°C

 

does not light during

(50°F to 95°F).

 

charging.

• When the battery is already fully charged, the lamp does

15

 

not light. Check the remaining battery power.

 

Recording cannot be

• Recording medium is full. Delete unnecessary fi les or

20

performed.

replace the microSD card.

 

• Select the recording medium properly.

–

 

During recording, the

• Touch the DISP button once.

13

date/time does not

 

 

appear.

 

 

During video recording,

• The temperature of the camera is increasing. If the

–

the 7REC indicator

camera continues to heat up, recording may be stopped

 

to protect the recording medium. In this case, turn off the

 

flashes.

 

power, and then wait until the camera cools down.

 

 

 

 

 

 

Digital zoom does not

• Change the settings in [ZOOM].

–

work.

• Digital zoom is not available in the still image recording

–

mode.

 

 

 

 

 

 

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Model No Serial No For Future ReferencePara futuras consultas Número de modelo Número de serieSelect playback Play mode Select recording REC modeEasy Start Guide Preparation Video recordingCamera turns on automatically To stop playbackSelect L For USA-California Only Safety PrecautionsTrademarks Important Safety InstructionsUsing on-screen buttons e.g. during playback  pg Read This FirstSelecting an item from the menu list on the menu screen Make a backup of important recorded data Contents How to Use the Everio Dock AccessoriesPower-linked operation IndexLCD monitor can rotate Camera Remote ControlWind Cut Indicator * Event Indicator Indications on LCD MonitorDuring Still Image Recording Only Switching indication modes on LCD monitor During Video PlaybackDuring Still Image Playback Necessary Settings before Use Charging the Battery PackDate/Time Setting Checking the Remaining Battery Power Other SettingsPreparing the Remote Control Attaching the Shoulder StrapRecording Files Video RecordingPress the START/STOP button to start recording Still Image Recording Slide the mode switch to select # still image modePress and hold the Snapshot button halfway Press the Snapshot button fully to take the photo/picturePlaying Back Files Video/Still Image PlaybackSelect the desired file Watching Images on TV Turn on the camera and the TV Set the TV to its Video mode169 TV To display the camera’s on-screen display onDeleting/Protecting Files Managing Files, select Cancel ALL Select YES To quit the screen Select Quit To release protectionTo release protection of all files Copying Files Using a DVD Burner to Copy Files from the CameraSystem Requirements File Backup on a Windows PCClick Easy Installation Software InstallationPowerProducer 3 NE Load the provided CD-ROM into the PCSoftware installation starts Connecting the Camera to the PCSelect the desired language and click OK Click Yes Click FinishFile Backup on the PC File Backup from a Specified Media PreparationFailing to do so may cause damage to the camera and PC File Backup on the PC without Using Software Click Everiohdd or Everio SDFor further details on the use of folders, see PowerDirector 5 NE Express Click PowerProducer User’s Guide or ReadmeOther Windows PC Operations Getting More Use of the SoftwareFolder Structure and Extensions = numberExtensions Connecting the Camera to the Macintosh File Backup on a MacintoshYou can back up camera fi les onto your computer HardwareUSB cable.  pg File Backup on the MacintoshTelephone/fax support Customer Support InformationPaid voice support Support web/e-mailTroubleshooting To reset the cameraFollowing phenomena are not malfunctions To clean the exterior CleaningTo clean the LCD monitor To clean the lensIndication Meaning/Action Battery indicatorAC Adapter SpecificationsApproximate recording time minutes for video Approximate number of storable images for still imageRequired charging/recording time approx Battery Packs Recording MediumLCD Monitor Main Unit Terms Memo Victor Company of Japan, Limited Términos
Top Page Image Contents