Kenwood KR-V888D instruction manual Connecting the system control

Page 12

Setting up the system

KR-V888D (En/T)

1 2 Connecting the system control

Preparations

Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations.

There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below.

ÄMode : lets you combine f, Ä, and F terminals Mode : for terminals only

This unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, follow the instructions in “SWITCHING FROM [SL16] TO [XS8]” below.

EXAMPLE: [XS8] mode connections

The underlined portion represents the setting of the system control mode.

[SL16] [XS8]

Receiver

 

 

 

 

 

 

[SL16]

MD recorder

 

 

 

 

 

SYSTEM

 

 

 

[SL16] [XS] [XS8] [XR]

Cassette deck

 

 

 

CONTROL

 

[SL16] [XS] [XS8]

 

 

cord

CD player

 

 

 

 

 

 

 

 

 

 

 

 

EXAMPLE: [SL16] mode connections

The underlined portion represents the setting of the system control mode.

[SL16] [XS8]

Receiver

 

 

 

 

 

 

 

 

 

 

[SL16]

MD recorder

 

SYSTEM

 

[SL16] [XS] [XS8] [XR]

 

 

 

 

Cassette deck

 

 

 

CONTROL

 

[SL16] [XS] [XS8]

 

 

cord

CD player

 

 

 

 

 

 

 

 

[XS]

Record player

[XS]

Record player

 

 

 

 

•In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must be connected to the CD jacks. To use a cassette deck (or MD recorder) it must be connected to the TAPE/MD jacks. When using more than one CD player (etc.) only the one connected to the specified jacks may be connected for system control.

•Some CD players and cassette decks are not compatible with the [SL16] system control mode. Be sure to use the [XS8] system control mode when making system connections with equipment that is not [SL16] compatible.

•Some MD players are not system control compatible. You cannot make system control connections to this kind of equipment.

1.[SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If your equipment consists of this kind of combination, please do not connect any system control cords. Even without

Notes

system control cords, normal operations can be carried out without effecting performance.

2. Do not connect system control cords to any components other than those specified by KENWOOD. It may cause a malfunction and damage your equipment.

3. Be sure the system control plugs are inserted all the way in to the system control terminals.

SYSTEM CONTROL OPERATIONS

Remote Control

Lets you operate this unit with the system remote supplied with the receiver.

Automatic Operation (except [XR] equipment)

When you start playback from a source component, the input selector on this unit switches to that component automatically.

Synchronized Recording (except [XR] equipment)

Lets you synchronize recording with the start of playback when recording from CD, MD or analog discs.

SWITCHING FROM [SL16] TO [XS8]

You can easily change the system control mode by adjusting the position of the SYSTEM CONTROL switch on the rear panel.

Do this operation after completing all connections.

For [SL16] SL 16 XS 8 For [XS8]

•This operation will not effect items stored in the memory.

•After switching the system control mode, turn the power off and then on once to confirm the new setting.

Registering setup codes for KENWOOD audio components

• Once you finish making the system connections, be sure to register the appropriate setup code for each component.

°

•If you own remote controllable KENWOOD audio components that are not compatible with system control (or cannot be combined with your other system control components), registering the setup code enables you to control those components using the remote control supplied with this unit (without connecting system control cords). To register setup codes for your remote controllable KENWOOD audio components, see

"Registering setup codes for other components".

°

Page 11 Page 13
Image 12
Page 11 Page 13
Contents About the supplied remote control KR-V888DSafety precautions AccessoriesGetting started UnpackingContents Special features Universal IR InfraRed remote controlTrue home theater sound How to use this manual Special featuresRDS Radio Data System tuner New Traitr transistor adopted in the final stageAbout the Standby indicator Names and functions of partsNames and functions of parts Setting up the system Connecting the antennasConnecting audio components Microcomputer malfunction6CH input M.INPUT System Control jacksConnecting video components Setting up the systemDigital connections AC-3 RF Demodulator DEM-999DConnecting the system control Registering setup codes for Kenwood audio componentsConnecting the speakers Speaker impedancePreparing the remote control PRE OUT connectionsLoading the batteries Operating distanceUsing the on-screen display Press the Sound or Setup keyTo quit the OSD mode Move the pointerSurround set up Speaker placementPreparing for surround sound Select the speakers and enter the speaker distance4Adjust the volume levels of each speaker Adjust the audio input level of the connected componentsEnter the speaker distance Normal playback Listening to a source componentAdjusting the sound Listening with headphones Source Direct playback6CH.INPUT playback Listening with a graphic equalizerSet the Input Selector to Video SecondsRecording Recording audioRecording video Recording a music sourceTuning non-RDSradio stations Select a tuning methodSet the input to tuner Select a broadcast bandTuning radio stations by frequency Direct tuning Listening to radio broadcasts3Enter the frequency Press the Direct keyUsing the Display key RDS functionsPresetting RDS stations RDS Auto Memory Receiving preset RDS stationsSet the broadcast band to FM Store the stations automaticallyPresetting radio stations manually Receiving preset stations in order P.CALLEnter a preset number 1~40 For 15, press For 20, pressTuning by program type PTY search Activate the PTY search modeSelect the program type you desire To select another program type Start the searchExample Searching for a Rock Music broadcast Tune to a preset RDS station Reserving the desired informationPreparation Stations RDS Auto MemoryTo cancel EON reservation When listening to the tunerTurn the TA, News and INFO. indicators off TP Traffic Program indicationAmbience effects Sound modesDolby Digital AC-3 Dolby Pro LogicDSP mode Whats DSP?Ambience effects Select a surround mode Surround PlayPreparations Source Direct S.DIRTo select a DSP mode To adjust the DSP modesConvenient functions OSD switch Source Direct switchSET UP switch Radio Text switchKR-V888D En/T Getting the most from your remote control Registering setup codes for other componentsFind the setup code of the component to be registered Low battery warningEnter the setup code 8Once setup codes have been entered for allPress the ENT key to store the code you have just input 7Repeat steps 3 to 6 to register additionalOperating other components Video key Audio key TV keyPress the operation keys you desire VIDEO1 VCR CD CD TV1 VIDEO2 VCRChanging confirming the operation mode Press ShiftSelect the component to be controlled Execute the desired operationsMake a plan of the macro play you want to set up Activate the macro program modePerform each of the following steps within 5 seconds Select where the macro should be stored Terminate the macro program modePress the keys to be operated in order Repeat steps 1 through 5 to program up to 3 macrosExecuting an automatic operation Press the Macro keyExecute the macro play Setup code correlation Deleting a setup codeChecking a setup code Perform each step within 5 secondsHold down the ENT key until the backlight flashes twice Enter the 3 digit codeUK including N. Ireland Go to within 5 secondsCode selection after mode download Hold your remote to the speaker portion of your telephonePress a numeric key Set up code chart VCR Set up codesMaker Set up codes Non-IR codesSet up code chart VCR Set up codesTV Set up codes BPLSatellite Set up codes LD player Set up codesDSS Set up codes DVD Set up codesCable Set up codes CD Player Set up codesDAT deck Set up codes Cassette deck Set up codesMD Set up codes Misc. audio Set up codesResetting the Microcomputer Case of difficultyAmplifier TunerRemote control unit Case of difficultyMemory back up function Specifications Remote operation of other components MD recorder operationsTuner operations TV operations VCR operationsLD player operations Satellite tuner operationsFunction Shift commands Menu Menu Theme Theme Cable tuner operationsDVD player operations + Channel + Select Numeric keysFor your records
Top Page Image Contents