Kenwood KR-V888D Preparing the remote control, PRE OUT connections, Loading the batteries

Page 14

1 4

Preparations

Setting up the system

KR-V888D (En/T)

PRE OUT connections

This receiver has additional preout jacks. These can be used for various purposes, but will need to be connected to an external power amplifier as shown in the example below. Connecting a speaker cord directly to a PRE OUT jack will not produce any sound from the speaker.

Be sure to set one of the SPEAKERS keys (either A or B) to the ON position when using the PRE OUT jacks.

PRE OUT

	SURROUND	CENTER
		Power amp	Center Speaker
Surround	Power amp	SUB	Powered
Speakers		WOOFER	Powered
Speakers			Subwoofer
			Subwoofer

Preparing the remote control

Loading the batteries

1 Remove the cover.

2 Insert the batteries.

3 Close the cover.

•Insert four AAA-size (LR03) batteries as indicated by the polarity markings.

1.The supplied batteries may have shorter lives than ordinary batteries due to use during operation checks.

Notes	2. Replace all four batteries with new ones when you notice a shortening of the distance from which the remote control will operate or if the
	remote control blinks 5 times when you push a key. The remote control is designed to retain set up codes in memory while you change
	batteries.

3.Placing the remote sensor in direct sunlight, or in direct light from a high frequency fluorescent lamp may cause a malfunction. In such a case, change the location of the system installation to prevent malfunction.

Operating distance

This remote control has two IR emitters: one to send commands in a straight line over long distances, allowing you to control the receiver and your other components from farther away; and one for wide dispersion of commands in a closer proximity, for near- field operation even when the remote control is not pointed directly at the respective component.

Remote sensor

6 m

10 m

30˚ 30˚

Model: RC-R0805 Infrared ray system

Image 14

Contents About the supplied remote control KR-V888DGetting started Safety precautionsAccessories UnpackingContents True home theater sound Special featuresUniversal IR InfraRed remote control RDS Radio Data System tuner How to use this manualSpecial features New Traitr transistor adopted in the final stageAbout the Standby indicator Names and functions of partsNames and functions of parts Setting up the system Connecting the antennas6CH input M.INPUT Connecting audio componentsMicrocomputer malfunction System Control jacksConnecting video components Setting up the systemDigital connections AC-3 RF Demodulator DEM-999DConnecting the system control Registering setup codes for Kenwood audio componentsConnecting the speakers Speaker impedanceLoading the batteries Preparing the remote controlPRE OUT connections Operating distanceTo quit the OSD mode Using the on-screen displayPress the Sound or Setup key Move the pointerPreparing for surround sound Surround set upSpeaker placement Select the speakers and enter the speaker distanceEnter the speaker distance 4Adjust the volume levels of each speakerAdjust the audio input level of the connected components Normal playback Listening to a source componentAdjusting the sound Listening with headphones Source Direct playbackSet the Input Selector to Video 6CH.INPUT playbackListening with a graphic equalizer SecondsRecording video RecordingRecording audio Recording a music sourceSet the input to tuner Tuning non-RDSradio stationsSelect a tuning method Select a broadcast band3Enter the frequency Tuning radio stations by frequency Direct tuningListening to radio broadcasts Press the Direct keyUsing the Display key RDS functionsSet the broadcast band to FM Presetting RDS stations RDS Auto MemoryReceiving preset RDS stations Store the stations automaticallyEnter a preset number 1~40 Presetting radio stations manuallyReceiving preset stations in order P.CALL For 15, press For 20, pressSelect the program type you desire Tuning by program type PTY searchActivate the PTY search mode Example Searching for a Rock Music broadcast To select another program typeStart the search Preparation Tune to a preset RDS stationReserving the desired information Stations RDS Auto MemoryTurn the TA, News and INFO. indicators off To cancel EON reservationWhen listening to the tuner TP Traffic Program indicationDolby Digital AC-3 Ambience effectsSound modes Dolby Pro LogicAmbience effects DSP modeWhats DSP? Preparations Select a surround modeSurround Play Source Direct S.DIRConvenient functions To select a DSP modeTo adjust the DSP modes SET UP switch OSD switchSource Direct switch Radio Text switchKR-V888D En/T Find the setup code of the component to be registered Getting the most from your remote controlRegistering setup codes for other components Low battery warningPress the ENT key to store the code you have just input Enter the setup code8Once setup codes have been entered for all 7Repeat steps 3 to 6 to register additionalPress the operation keys you desire Operating other componentsVideo key Audio key TV key VIDEO1 VCR CD CD TV1 VIDEO2 VCRSelect the component to be controlled Changing confirming the operation modePress Shift Execute the desired operationsPerform each of the following steps within 5 seconds Make a plan of the macro play you want to set upActivate the macro program mode Press the keys to be operated in order Select where the macro should be storedTerminate the macro program mode Repeat steps 1 through 5 to program up to 3 macrosExecute the macro play Executing an automatic operationPress the Macro key Checking a setup code Setup code correlationDeleting a setup code Perform each step within 5 secondsUK including N. Ireland Hold down the ENT key until the backlight flashes twiceEnter the 3 digit code Go to within 5 secondsPress a numeric key Code selection after mode downloadHold your remote to the speaker portion of your telephone Maker Set up codes Set up code chartVCR Set up codes Non-IR codesSet up code chart VCR Set up codesTV Set up codes BPLDSS Set up codes Satellite Set up codesLD player Set up codes DVD Set up codesCable Set up codes CD Player Set up codesMD Set up codes DAT deck Set up codesCassette deck Set up codes Misc. audio Set up codesAmplifier Resetting the MicrocomputerCase of difficulty TunerMemory back up function Remote control unitCase of difficulty Specifications Tuner operations Remote operation of other componentsMD recorder operations LD player operations TV operationsVCR operations Satellite tuner operationsDVD player operations Function Shift commands Menu Menu Theme ThemeCable tuner operations + Channel + Select Numeric keysFor your records