Kenwood KR-V888D instruction manual Getting started, Safety precautions, Unpacking, Accessories

Page 2

2

Preparations

Getting started

Before applying the power

Units are designed for operation as follows.

U.K. and Europe

AC 230 V only

For the United Kingdom

Factory fitted moulded mains plug

1.The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.

2.The fuse cover must be refitted when replacing the fuse in the moulded plug.

3.Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

IMPORTANT

The wires in the mains lead are coloured in accordance with the

following code: Blue : Neutral Brown : Live

Do not connect those leads to the earth terminal of a three-pin plug.

Caution : Read this page carefully to ensure safe operation.

KR-V888D (En/T)

REQUIREMENT BY NEDERLAND GAZETTE

Batteries are supplied with this product. When they empty, you should not throw away. In- stead, hand them in as small chemical waste.

Safety precautions

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

 

CAUTION

 

 

 

 

BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE

 

RISK OF ELECTRIC SHOCK

 

 

DO NOT OPEN

 

PERSONNEL.

 

 

 

 

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

Unpacking

Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.

Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage.

We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.

Accessories

FM indoor antenna (1)

AM loop antenna (1)

Loop antenna stand (1)

Remote control unit (1)

Batteries (R03/AAA) (4)

RF DEMODULATOR (1)

 

LASER

DISC RF

 

 

POWERDEMODULATOR DEM-

 

 

LOCK 999D

AC adaptor (1) Power cord (1) RCA pin cord (2)

Page 1 Page 3
Image 2
Page 1 Page 3
Contents About the supplied remote control KR-V888DGetting started Safety precautionsAccessories UnpackingContents True home theater sound Special featuresUniversal IR InfraRed remote control RDS Radio Data System tuner How to use this manualSpecial features New Traitr transistor adopted in the final stageAbout the Standby indicator Names and functions of partsNames and functions of parts Setting up the system Connecting the antennas6CH input M.INPUT Connecting audio componentsMicrocomputer malfunction System Control jacksConnecting video components Setting up the systemDigital connections AC-3 RF Demodulator DEM-999DConnecting the system control Registering setup codes for Kenwood audio componentsConnecting the speakers Speaker impedanceLoading the batteries Preparing the remote controlPRE OUT connections Operating distanceTo quit the OSD mode Using the on-screen displayPress the Sound or Setup key Move the pointerPreparing for surround sound Surround set upSpeaker placement Select the speakers and enter the speaker distanceEnter the speaker distance 4Adjust the volume levels of each speakerAdjust the audio input level of the connected components Normal playback Listening to a source componentAdjusting the sound Listening with headphones Source Direct playbackSet the Input Selector to Video 6CH.INPUT playbackListening with a graphic equalizer SecondsRecording video RecordingRecording audio Recording a music sourceSet the input to tuner Tuning non-RDSradio stationsSelect a tuning method Select a broadcast band3Enter the frequency Tuning radio stations by frequency Direct tuningListening to radio broadcasts Press the Direct keyUsing the Display key RDS functionsSet the broadcast band to FM Presetting RDS stations RDS Auto MemoryReceiving preset RDS stations Store the stations automaticallyEnter a preset number 1~40 Presetting radio stations manuallyReceiving preset stations in order P.CALL For 15, press For 20, pressSelect the program type you desire Tuning by program type PTY searchActivate the PTY search mode Example Searching for a Rock Music broadcast To select another program typeStart the search Preparation Tune to a preset RDS stationReserving the desired information Stations RDS Auto MemoryTurn the TA, News and INFO. indicators off To cancel EON reservationWhen listening to the tuner TP Traffic Program indicationDolby Digital AC-3 Ambience effectsSound modes Dolby Pro LogicAmbience effects DSP modeWhats DSP? Preparations Select a surround modeSurround Play Source Direct S.DIRConvenient functions To select a DSP modeTo adjust the DSP modes SET UP switch OSD switchSource Direct switch Radio Text switchKR-V888D En/T Find the setup code of the component to be registered Getting the most from your remote controlRegistering setup codes for other components Low battery warningPress the ENT key to store the code you have just input Enter the setup code8Once setup codes have been entered for all 7Repeat steps 3 to 6 to register additionalPress the operation keys you desire Operating other componentsVideo key Audio key TV key VIDEO1 VCR CD CD TV1 VIDEO2 VCRSelect the component to be controlled Changing confirming the operation modePress Shift Execute the desired operationsPerform each of the following steps within 5 seconds Make a plan of the macro play you want to set upActivate the macro program mode Press the keys to be operated in order Select where the macro should be storedTerminate the macro program mode Repeat steps 1 through 5 to program up to 3 macrosExecute the macro play Executing an automatic operationPress the Macro key Checking a setup code Setup code correlationDeleting a setup code Perform each step within 5 secondsUK including N. Ireland Hold down the ENT key until the backlight flashes twiceEnter the 3 digit code Go to within 5 secondsPress a numeric key Code selection after mode downloadHold your remote to the speaker portion of your telephone Maker Set up codes Set up code chartVCR Set up codes Non-IR codesSet up code chart VCR Set up codesTV Set up codes BPLDSS Set up codes Satellite Set up codesLD player Set up codes DVD Set up codesCable Set up codes CD Player Set up codesMD Set up codes DAT deck Set up codesCassette deck Set up codes Misc. audio Set up codesAmplifier Resetting the MicrocomputerCase of difficulty TunerMemory back up function Remote control unitCase of difficulty Specifications Tuner operations Remote operation of other componentsMD recorder operations LD player operations TV operationsVCR operations Satellite tuner operationsDVD player operations Function Shift commands Menu Menu Theme ThemeCable tuner operations + Channel + Select Numeric keysFor your records
Top Page Image Contents