Kenwood KR-V888D Enter the setup code, Press the ENT key to store the code you have just input

Page 39
The backlight flashes twice.
ENT
POWER
DISPLAY
0
8
REPEAT
5
2
THEME

4Enter the setup code.

MENUFAV

13

TV/SAT/VID INFO

ALT AUD

46

+100RANDOM

79

Getting the most from your remote control

KR-V888D (En/T)

3 9

•Example: Press 5258 to register a LD player made by KENWOOD.

•The backlight flashes once each time a number is entered.

•If an invalid setup code is entered the remote will output one long blink, disregard that code and return to the beginning of step 4.

•If you push an invalid key, the remote will exit the setup mode.

5Press POWER, and check to see that the component you want to control turns on.

• PLAY or TUNING/SKIP (+/–) can also be used instead of POWER.

• If the component does not react, and there is more than one setup code, enter another setup code and try again.

• If the component is already on, pressing POWER will turn it off.

6Press the ENT key to store the code you have just input.

• This code replaces any previous setup codes entered for the respective component.

 

• If you have components that are not remote controllable, like a record

7Repeat steps 3 to 6 to register additional

player (etc.), you will need to register a dummy code at the respective

input. This keeps the respective input in the remote control's cyclic list

so you can select it using the remote control. Please consult the

components until all components have been

owner's manual of the components you are connecting for information

registered.

regarding remote controllability. The list of dummy codes is included at

8Once setup codes have been entered for all

the beginning of the Set up code chart.

i

 

 

components, hold down the ENT key until

 

 

the backlight flashes twice.

• This operation should take about 3 seconds.

 

 

• Once registered, the display on the receiver shows the component

 

type instead of the default input name.

 

 

Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears

 

instead of "VIDEO 1(SAT)".

 

ENT

• Both the default input name and the component type (i.e., " VIDEO1

 

'VCR' ") are shown in the on screen display when the OSD mode is set

 

to ON.

ß

 

• After initial setup, any VIDEO (VIDEO 1, 2, 3) or TV (TV1, TV2, CABLE)

 

inputs that have not been programmed with a setup code or Non-IR

 

code are deleted from the cyclic list (except for the "AV AUX" VIDEO

 

input). The PHONO input will be deleted if a Non-IR code was not

 

registered.

 

 

• The INPUT SELECTOR on the front panel of the receiver always cycles

 

through all inputs.

 

 

 

Although each setup code is designed to work with a number of different models, certain codes may not work with some models. (Also,

Note

certain codes may only operate some of the functions available on a given model.)

Remote Control

Page 38 Page 40
Image 39
Page 38 Page 40
Contents KR-V888D About the supplied remote controlUnpacking Safety precautionsAccessories Getting startedContents Special features Universal IR InfraRed remote controlTrue home theater sound New Traitr transistor adopted in the final stage How to use this manualSpecial features RDS Radio Data System tunerNames and functions of parts About the Standby indicatorNames and functions of parts Connecting the antennas Setting up the systemSystem Control jacks Connecting audio componentsMicrocomputer malfunction 6CH input M.INPUTSetting up the system Connecting video componentsAC-3 RF Demodulator DEM-999D Digital connectionsRegistering setup codes for Kenwood audio components Connecting the system controlSpeaker impedance Connecting the speakersOperating distance Preparing the remote controlPRE OUT connections Loading the batteriesMove the pointer Using the on-screen displayPress the Sound or Setup key To quit the OSD modeSelect the speakers and enter the speaker distance Surround set upSpeaker placement Preparing for surround sound4Adjust the volume levels of each speaker Adjust the audio input level of the connected componentsEnter the speaker distance Listening to a source component Normal playbackAdjusting the sound Source Direct playback Listening with headphonesSeconds 6CH.INPUT playbackListening with a graphic equalizer Set the Input Selector to VideoRecording a music source RecordingRecording audio Recording videoSelect a broadcast band Tuning non-RDSradio stationsSelect a tuning method Set the input to tunerPress the Direct key Tuning radio stations by frequency Direct tuningListening to radio broadcasts 3Enter the frequencyRDS functions Using the Display keyStore the stations automatically Presetting RDS stations RDS Auto MemoryReceiving preset RDS stations Set the broadcast band to FMFor 15, press For 20, press Presetting radio stations manuallyReceiving preset stations in order P.CALL Enter a preset number 1~40Tuning by program type PTY search Activate the PTY search modeSelect the program type you desire To select another program type Start the searchExample Searching for a Rock Music broadcast Stations RDS Auto Memory Tune to a preset RDS stationReserving the desired information PreparationTP Traffic Program indication To cancel EON reservationWhen listening to the tuner Turn the TA, News and INFO. indicators offDolby Pro Logic Ambience effectsSound modes Dolby Digital AC-3DSP mode Whats DSP?Ambience effects Source Direct S.DIR Select a surround modeSurround Play PreparationsTo select a DSP mode To adjust the DSP modesConvenient functions Radio Text switch OSD switchSource Direct switch SET UP switchKR-V888D En/T Low battery warning Getting the most from your remote controlRegistering setup codes for other components Find the setup code of the component to be registered7Repeat steps 3 to 6 to register additional Enter the setup code8Once setup codes have been entered for all Press the ENT key to store the code you have just inputVIDEO1 VCR CD CD TV1 VIDEO2 VCR Operating other componentsVideo key Audio key TV key Press the operation keys you desireExecute the desired operations Changing confirming the operation modePress Shift Select the component to be controlledMake a plan of the macro play you want to set up Activate the macro program modePerform each of the following steps within 5 seconds Repeat steps 1 through 5 to program up to 3 macros Select where the macro should be storedTerminate the macro program mode Press the keys to be operated in orderExecuting an automatic operation Press the Macro keyExecute the macro play Perform each step within 5 seconds Setup code correlationDeleting a setup code Checking a setup codeGo to within 5 seconds Hold down the ENT key until the backlight flashes twiceEnter the 3 digit code UK including N. IrelandCode selection after mode download Hold your remote to the speaker portion of your telephonePress a numeric key Non-IR codes Set up code chartVCR Set up codes Maker Set up codesVCR Set up codes Set up code chartBPL TV Set up codesDVD Set up codes Satellite Set up codesLD player Set up codes DSS Set up codesCD Player Set up codes Cable Set up codesMisc. audio Set up codes DAT deck Set up codesCassette deck Set up codes MD Set up codesTuner Resetting the MicrocomputerCase of difficulty AmplifierRemote control unit Case of difficultyMemory back up function Specifications Remote operation of other components MD recorder operationsTuner operations Satellite tuner operations TV operationsVCR operations LD player operations+ Channel + Select Numeric keys Function Shift commands Menu Menu Theme ThemeCable tuner operations DVD player operationsFor your records
Top Page Image Contents