40 EN TROUBLESHOOTING
If the problem still exists after following the steps below, please consult your nearest JVC dealer.
The camcorder is a
Power
No power is supplied.
●The power is not connected properly.
HConnect the AC Adapter securely. ( pg. 7)
●The battery is dead.
HReplace the dead battery with a fully charged one. ( pg. 6, 7)
●The LCD monitor is not open fully or the viewfinder is not pulled out when recording.
HOpen the LCD monitor fully or pull out the viewfinder.
The POWER/CHARGE lamp blinks in the Record- Standby mode.
●If the
Then, the POWER/CHARGE lamp will blink to indicate for charging if the battery pack is attached to the camcorder and its power is supplied from the AC Adapter.
HPush back and pull out the viewfinder again or close and
Video and D.S.C. Recording
Recording cannot be performed.
●The Power Switch is set to “PLAY” or “OFF”.
HSet the Power Switch to “A” or “M”. ( pg. 11, 18)
— For Video Recording —
●The tape’s erase protection tab is set to “SAVE”.
HSet the tape’s erase protection tab to “REC”. ( pg. 10)
●The VIDEO/MEMORY Switch is set to “MEMORY”. HSet the VIDEO/MEMORY Switch to “VIDEO”.
●“TAPE END” appears.
HReplace with new cassette. ( pg. 10)
●The cassette holder cover is open. HClose the cassette holder cover.
— For D.S.C. Recording —
●The VIDEO/MEMORY Switch is set to “VIDEO”. HSet the VIDEO/MEMORY Switch to “MEMORY”.
During recording, the date/ time does not appear.
●“DATE/TIME” is set to “OFF”.
HSet “DATE/TIME” to “ON”. ( pg. 25, 27)
During recording, sound cannot be heard.
●This is normal.
The LCD monitor or viewfinder indications blink.
●Certain Wipe/Fader effects, certain modes of Program AE with special effects, “DIS” and other functions that cannot
be used together are selected at the same time.
Program AE with special effects and “DIS”. ( pg. 25 – 31)
Digital Zoom does not work.
●10X optical zoom is selected.
HSet “ZOOM” to “40X” or “700X”. ( pg. 26)
●The VIDEO/MEMORY Switch is set to “MEMORY”. HSet the VIDEO/MEMORY Switch to “VIDEO”.
Colored bright spots appear all over the LCD monitor.
●White spots or bright spots of light (red, green or blue) may appear on the LCD monitor. This may occur when the
Video and D.S.C. Playback
Play, Rewind and Fast-Forward functions do not work.
●The Power Switch is set to “A” or “M”.
HSet the Power Switch to “PLAY”. ( pg. 14)
●VIDEO/MEMORY Switch is set to “MEMORY”. HSet the VIDEO/MEMORY Switch to “VIDEO”.
The tape is moving, but there is no picture.
●Your TV has AV input terminals, but is not set to its VIDEO mode.
HSet the TV to the mode or channel appropriate for video playback. ( pg. 17)
●The cassette holder cover is open.
HClose the cassette holder cover. ( pg. 10)
Blocks of noise appear during playback, or there is no playback picture and the screen becomes blue.
HClean the video heads with an optional cleaning cassette. ( pg. 46)
A memory card cannot be played back.
When shooting a subject illuminated by bright light, vertical lines appear.
●This is a result of exceedingly high contrast, and is not a malfunction.
●The Power Switch is set to “A” or “M”.
HSet the Power Switch to “PLAY”. ( pg. 20)
●The VIDEO/MEMORY Switch is set to “VIDEO”. HSet the VIDEO/MEMORY Switch to “MEMORY”.
When the screen is under direct sunlight during shooting, the screen becomes red or black for an instant.
●This is not a malfunction.