Panasonic DVC20 Recording, Inserted, Cassette cannot be inserted, Time code becomes inaccurate

DVC20_Eng.book 34 ページ ２００５年１０月３１日 月曜日 午前１０時３６分

Others

Recording

1:Recording does not start although power is supplied to the camera-recorder and the cassette is correctly

inserted.

•Is the accidental erasure prevention slider on the cassette open? If it is open (set to [SAVE]), recording cannot be performed. (-11-)

•Is the tape wound to the end? Insert a new cassette.

•Is the recording mode set? When in the playback mode, recording cannot be performed. (-18-)

•Has condensation occurred? No operation other than cassette removal can be performed when condensation occurs. Wait until the condensation indication disappears. (-35-)

•Is the cassette cover open? If the cover is open, the camera-

recorder may not operate normally. Close the cassette cover. (-11-)

2: A cassette cannot be inserted.

•Has condensation occurred? Wait until the condensation indication disappears.

3: Auto focus function does not work.

•Is manual focus mode selected? If auto focus mode is selected, focus is automatically adjusted.

•There are some recording subjects and surroundings for which the auto focus does not operate correctly. (-38-) If so, use the manual focus mode to adjust the focus. (-24-)

•Is the color night view function set? When the color night view function is working, focusing shifts into the manual mode.

Indications

1:A sentence is displayed in red or yellow in the screen center.

•Read the contents and respond to them. (-32-)

2: The time code becomes inaccurate.

0 The time code indication counter may not be constant in the reversed slow-motion playback, but this is not a malfunction.

3: The remaining tape time indication disappears.

•The remaining tape time indication may disappear temporarily during frame-by-frame playback or other operation. If you continue ordinary recording or playback, the indication is restored.

4: The remaining tape time Indication does not match the actual remaining tape time.

•If scenes of less than 15 seconds are continuously recorded, the remaining tape time cannot be correctly displayed.

•In some cases, the remaining tape time indication may show remaining tape time that is 2 to 3 minutes shorter than the

actual remaining tape time.

5:A function indication such as mode indication, remaining tape time indication, or time code indication is

not shown.

•If you set [SETUP] >> [DISPLAY] >> [OFF], indications other than the tape running condition, warning, and date indications disappear.

Playback (Sound)

1:Sound is not played back from the built-in speaker of the camera-recorder or the headphones.

0Is the volume too low? During playback, push the [W/T] lever

to display the volume indication and adjust it. (-25-)

2: Different sounds are reproduced at the same time.

•Have you set [SETUP] >> [12bit AUDIO] >> [MIX]? If you set [AUDIO REC] >> [12bit] and dub audio to a recorded tape, you can hear the sound on recording and the sound dubbed at a later time. To hear the sounds separately, set to [ST1] or [ST2]. (-29-)

•Have you set [SETUP] >> [AUDIO OUT] >> [STEREO] and reproduced a picture containing the main sound and sub sound? Set to [L] to hear main sound, and set to [R] to hear

the sub sound. (-31-)

3: Audio dubbing cannot be performed.

•Is the accidental erasure prevention slider on the cassette open? If it is open (set to [SAVE]), audio dubbing cannot be performed. (-11-)

•Are you attempting to edit a tape portion that was recorded in LP mode? LP mode does not allow audio dubbing. (-18-)

4:The original sound was erased when audio dubbing was performed.

•If you perform audio dubbing on a recording made in [16bit] mode, the original sound will be erased. If you wish to

preserve the original sound, be sure to select [12bit] mode when recording.

5: Sounds cannot be played back.

•Although a cassette with no audio dubbing is being played, have you set [SETUP] >> [12bit AUDIO] >> [ST2]? To play back a cassette with no audio dubbing, set [12bit AUDIO] >> [ST1]. (-29-)

•Is the variable speed search function working? Press the [VAR. SEARCH] button on the remote control to cancel the variable speed search function. (-26-)

Playback (Pictures)

1: Mosaic-pattern noise appears on images during cue or review playback.

• This phenomenon is characteristic of digital video systems. It is not a malfunction.

2: Horizontal stripes appear on images during cue and review playback.

• Horizontal stripes may appear depending on the scene, but this is not a malfunction.

3: Although the camera-recorder is correctly connected to a TV, playback images cannot be seen.

•Have you selected video input on the TV? Please read the operating instructions of your TV and select the channel that

matches the input terminals used for the connection.

4: Playback picture is not clear.

•Are the heads of the camera-recorder dirty? If the heads are dirty, playback image cannot be clear. Clean the heads by using the head cleaner for digital video. (-35-)

•If the terminal for the AV cable is soiled, noises may appear on the screen. Wipe the soil off the terminal with a soft cloth, and then connect the cable to the AV terminal.

•Is a picture containing a copyright protection signal (copy guard) being recorded? When a protected picture is played back by the camera-recorder, mosaic-like patterns appear on the picture.

34