Panasonic AJ-HDX400E operating instructions Time code related section, Ctl

Page 16

Chapter 2 Parts and their functions

2-5 Time code related section

4 5 6

9

1 3 2

1 GENLOCK IN connector (BNC)

The HD Y reference signal is supplied to this connector when the camera unit is to be gen-locked or the time code is to be externally locked. It is also possible to supply PAL composite video signals instead as the reference signal.

2 TC IN connector (BNC)

Supply the time code which will serve as the reference to this connector when externally locking the time code.

3 TC OUT connector (BNC)

To lock the time code of an external VTR to the unit’s time code, connect this connector to the time code input (TC IN) connector on the external VTR.

4 HOLD button

The time data display of the counter display section which was on the screen at the moment when this button is pressed is held. (However, the time code generator keeps running.) When the button is pressed again, the hold status is released.

It is used, for instance, to find out the time code or CTL counter value at which a particular scene was shot.

5 RESET button

This is used to reset the time data on the counter display section to “00:00:00:00.” If it is pressed while the TCG switch 9 is at the SET position, the time code data and user bits data are respectively reset to “00:00:00:00.”

6 DISPLAY switch

This is used to display the time code, CTL or user bits on the counter display section depending on the setting positions of this switch and the TCG switch 9.

UB

: The user bits are displayed.

TC

: The time code is displayed.

CTL

: CTL is displayed.

8 7

7 “+” button, “–” button

These are used to increment or decrement by 1 the figure in the digit which was made to flash by the SHIFT button 8 when the time code or user bits are to be set.

8 SHIFT button

This causes the digit to be set to flash when the time code or user bits are to be set.

9 TCG (time code selector) switch

This is used to set the running mode of the built-in time code generator.

F-RUN :Set here to have the time code run all the time regardless of the VTR’s operation.

This position is used to align the time code with the time or externally lock the time code.

SET : Set here when the time code or user bits are to be set.

R-RUN :Set here to have the time code run only during recording. The time code on the tape with scene- to-scene continuity is recorded continuously.

16

Image 16
Contents Operating Instructions Lithium Battery VarningTo remove the battery/Verwijderen van de batterij Contents Chapter Specifications Chapter Maintenance InspectionsMenu description tables Features of the camera unit Features of the VTR unit System configuration Video camera-recorder AJ-HDX400Power supply and accessory mounting section Front Audio function section input systemRear Audio function section output system Shooting and recording camera unit Shooting and recording VTR unit CAM. Auto Knee onCAM. Auto Knee OFF BarsScrop LT BOXSqueeze Setup card insertion slot Busy operation mode display lampMenu operation section Menu buttonTime code related section CTLRemaining tape and remaining battery charge Displays relating to the VTR unit’s operations and modesTime code-related switch settings and display items Mode displaysTCG switch position Display switch Display item Position Displays relating to the time codeViewfinder section Cassette tapes From providing the power supply to loading the cassette Basic proceduresUp to performing the switch settings Procedure for shooting Adjust the white balance3When adjusting the white balance on the spot Tape function buttonsPRE-RECORDING function Scene-to-scene continuityScene-to-scene continuity during rec-pause Interval REC function When the ONE Shot mode of Interval REC is to be exited When the Retake function is to be exitedRetake function Checkpoints common to all Interval REC modesRec-review function Normal playback and playback at different speedsDirection of tape travel Rec-pause To 10 sec Rec-review operation Rec-pauseAdjusting the white balance and black balance Adjusting the white balanceWhite balance detection area Output CAMWhen there is no time to adjust the white balance When the white balance cannot be adjusted automaticallyMessages relating to white balance adjustment White balance memoriesAdjusting the black balance Auto W/B BAL switchBlack balance memory Use this to execute ABBSetting the electronic shutter Setting the shutter mode and speedShutter modes Viewfinder screen displays relating to the shutterSelecting the recording signals and recording system Setting the synchro scan modeSelecting the recording signals Selecting the audio input signalsAdjusting the audio signal recording levels 3 CH3 and CH4 recording levelsAuto Level MICSetting the time data Setting the user bitsUser bit memory function Tape continuity with the user bitsSetting the internal clock’s date and time RegionSetting the time code Time code when the battery is replacedOperating procedure for external locking Externally locking the time codeSetting the Umid information Concerning the user bit setting during external lockTo release the external lock ExamplesMenu displays on the viewfinder screen Menu configurationBasic menu operations Selecting the user menus To increment the valueTo decrement the value To set an item to on or OFFViewfinder screen status display configuration Viewfinder screen status displaysViewfinder lamp displays Selecting the viewfinder screen display itemsDisplay item What is displayed Status when display appears Mode CheckCheck Filter Line MIX Gain Battery type Remaining batteryIris override ? Iris, f-valueColor temperature Viewfinder screen display selectionShutter Speed/modeSetting the camera ID Setting the marker displaysSetting change/adjustment result messages and display modes Mode check screen displays Mode Check button function Marker check screen displays Marker Select button functionMenu-driven function setup Setting the User SW Gain switchingSelecting the video output signals Setting items and detailsSelecting the F.AUDIO Level control function Setting items and what is setFunctions which can be selected Handling the setup card Setting the color temperature manuallyData handling Setup card operations Formatting the setup cardSaving the data settings on the card Selecting the file NoSaving the data settings to the selected file Giving a title to the selected fileLoading the data saved on the card Loading the data of the selected fileWriting the setting data in the user area How to use the user dataLoading the user data Writing the setting data used for the scene files How to use the scene file dataReading the setting data used for the scene files Scene Read User Data # Scene SEL Write Reset # Read Scene Read User Data Scene SEL1 Write Reset White BAL switch How to use the lens file dataOperation method without performing File menu operations Supplying the power Attaching the battery and setting the battery typeUsing the Anton Bauer battery pack ReferenceUsing the V-mount type battery pack Using the NP-1 type battery packNP-1 type Battery case Using an AC power supply When the AJ-B75 AC adapter made by Panasonic is usedPin no Signal +12VLens socket Adjusting the lens flangeApprox meters Adjusting the white shading of the lens Storing the lens file data Giving a title to the selected file noReading the lens file data Audio input signal preparations When using the front microphoneWhen using a wireless receiver When using a UniSlot wireless receiverWhen using an audio component Mounting the unit on a tripodDetaching the unit from the tripod adapter Tripod adapter Tripod headAdjusting the position of the shoulder pad Connecting the extension control unit AJ-EC3EAttaching the shoulder belt Example showing use of the SHAN-RC700 rain coverAttaching the Front Audio Level control knob Front AudioPreparation for inspections Inspections prior to shootingInspecting the camera unit Automatic audio level adjustment function inspection Manual audio level adjustment function inspectionInspecting the VTR unit Tape travel inspectionSelf-diagnosis function Inspection using external microphonesInspections relating to the time code and user bits Maintenance Connectors and signals PushNC5FBH HA16PRM-3SGBattery END SlackTape END REC WarningBattery Near END Wireless RFServo Tape Near ENDEmergency eject Error codesRemove the cassette How to open the menus Menu configurationHow to interpret the menu lists System Mode Camera ModeREC Function Output SELGenlock Option Mode1 ROP Matrix Color CorrectionLOW Setting MID SettingHigh Setting Additional DTLSkin Tone DTL KNEE/LEVELDirection =SKIN Tone Area$ Camera Settings GammaFlare STDVF Displays VF MarkerZebra pattern display HoldVF INDICATOR2 VF INDICATOR1User BOX Mode Check IND 7 !LEDCamera ID Shutter SpeedShutter Select User SWSW Mode SmpteSplit AribWhite Balance Mode User SW GainFile IrisCard READ/WRITE Card R/W SelectDiagnostic Lens FileSystem Check InitializeBATTERY/TAPE Black ShadingWhite Shading VTR FunctionManual Battery SETTING1HYTRON100 ENDURA50*1 ENDURA80*1ENDURA-D*2 NP-1BDIGITAL14 Battery SETTING2END 5 MIC/AUDIO1 6 MIC/AUDIO27 TC/UB Umid SET/INFODowncon Setting VTR DiagOption Data storage RangeVideo System Audio SystemTime Code Input Connector Time Code Output ConnectorOther Connectors Audio Output ConnectorsPanasonic Broadcast Europe Panasonic Marketing Europe GmbH