Panasonic AW-RP50N operating instructions Diag Speed, Scope Mode a

Page 21

Setting the functions

￿￿Setting the speed at which to move to the position set by the preset memory

The speed at which to move to the position where the remote camera has been set to be in the preset memory when the preset operation is conducted can be set.

From the [SETUP] menu, select [PRESET] and display [DIAG SPEED]. Then set the speed.

The higher the setting, the faster the operating speed.

1.DIAG SPEED ▼

1

￿￿Setting the operations to be performed when a preset operation is executed

The operations which the remote camera is to performed when the preset operation is conducted can be set.

From the [SETUP] menu, select [PRESET] and display [SCOPE].Then set the operations to be performed.

2.SCOPE

MODE A

The operations that the camera performs when a preset operation is executed differ depending on the mode selected.

Mode

Operations performed

MODE A

Pan, tilt, zoom, focus, iris, gain, white balance

MODE B

Pan, tilt, zoom, focus, iris

MODE C

Pan, tilt, zoom

Note

This function takes effect when the unit is connected to the AW-HE50. It does not work with any other models.

￿￿Adjusting the panning, tilting, zooming and focusing speed

The speed is adjusted uniformly for the panning, tilting, zooming and focusing together.

When the PTZ/FOCUS SPEED dial is turned clockwise, the speed is increased; conversely, when it is turned counterclockwise, it is reduced.

 

1

2

3

4

5

IRIS

AUTO

CAMERA STATUS / SELECTION

PT ACTIVE

 

 

 

AUTO

LE

ZOOM

LOW HI

WIDE

FOCUS/PUSH OAF

PTZ/FOCUS SPEED PAN/TILT

From the [SETUP] menu, select [OPERATE] and display [SPEED TARGET]. If P/T is selected, the speed adjustment is confined to panning and tilting only.

In this case, the zooming and focusing speed is fixed to the speed which was set immediately before P/T was selected.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operating Instructions Contents Before use How to turn the power of the remote cameras on How to turn the power of the remote cameras on and offRegistering data in the preset memories Setting and operating the preset memoriesHold down the Preset MEMORY/MENU button of the number on Preset numbers and registered pagesExecuting the preset data Deleting the preset memory dataHold down the Preset MEMORY/MENU button for the number on Selecting the settings for a selected remote camera Setting the gainSetting the pedestal Setting the R and B pedestal Setting the R and B gain valuesSet the Preset MEMORY/MENU 2 button R/B Gain to on Set the Preset MEMORY/MENU 3 button R/B PED to onSet the Preset MEMORY/MENU 4 button AWB/ABB to on Setting the white balanceTurn the F1 dial to select the white balance mode Selecting the white balance modeAutomatically adjusting the white balance AWB Mode AWB a SETTurn the F2 dial to select AWB, and press the F2 dial Automatic color temperature tracking ATW Manually adjusting the white balanceAWB Mode ATW SET Turn the F1 dial to select ATWAutomatically adjusting the black balance Setting the black balanceAWB Mode AWB B SET ABB Manually adjusting the black balanceSetting the detail Setting the shutter speedSet the Preset MEMORY/MENU 5 button Shutter to on Turn the F1 dial to select the shutter modeSet the Preset MEMORY/MENU 7 button SCENE/MODE to on Setting the shooting modeTurn the F1 dial to select the shooting mode Specifying the color barsTable of operations Operating the menu items of the selected remote cameraSet the Preset MEMORY/MENU 9 button Setup to on Setting the User buttonsRegistering functions User buttons SwlinkTurn the F1 dial to select the target menu item Setting the functionsSetting the pan, tilt, zoom and focus operation directions Setting the remote camera operationsZoom DIR Normal Focus DIR NormalSpeed with Z Off Selecting the control items pan, tilt, zoom and focusSpeed Target Z/FSetting the PAN/TILT lever inclination and speed Switching from focus control to iris control or vice versaFOCUS/IRIS Normal T CurvDiag Speed Scope Mode aSetting the lower limit Setting the upper limitSetting the right limit Setting the left limitHome Position SET Returning the remote cameras to their home position6FUNCTION Adjusting the minimum lens zoom start speed Adjusting the minimum pan/tilt start speedT MIN Speed Start MIN Speed10MENU CTL Setting button operation enable or disable 8GPI Setting the preset numbersMenu Control Enable Locking the button operationsSwitcher network settings Linking the unit with the switcherSet Preset MEMORY/MENU 10 button System to on IpswTurn the F1 dial to select the input line of the switcher Setting the image output and image input1CAMERA CTL 3SW AssignSet Preset MEMORY/MENU 9 button Setup to on Switcher settingsTurn the F1 dial to select the menu item to be set 2SW LinkBUS AUX Fasist OffCamsel Off Tallyip Off T LeverSelf Setting all the information displays together Setting for the information to be displayed on the OSDTurn the F1 dial to and select the menu item to be set 3SW DispSetting each information item to be displayed 8ALARM Checking the equipment alarm informationPower No Alarm Turn the F2 dial to display the remote camera itemTurn the F2 dial to select the initializing mode Press the F2 dial to initialize the settingsReturning the unit to its factory status Sub 15-pin, female, inch thread Control interface for external devicesExample of GPIOut connections Current Max mA AW-RP50Installing the software RP setting toolIP settings Software provided on the CD-ROMChanging the IP addresses Auto IP settingChanging the camera numbers Click RenewDisplaying the camera names Alarm displaysInitializing the IP addresses Acquiring informationSaving and loading data Saving the setting filesSystem section, click Save under From AW-RP50 Input the filename, and click SaveSaving the log files Loading the setting filesPedestal AW-HE50 Table of menu itemsVideo Setup Setup PTZ ADJ MIN Speed Start Limit UP AW-HE50 F0410Y0 Operating Instructions Basics FCC Note Safety precautionsImportant Safety Instructions Before use Overview Before use Characteristics Accessories Pan-tilt heads and cameras supportedPan-tilt heads supported CPU Required personal computer environmentConnecting the power supply Installation precautionsChoosing the best installation location Handle carefullyOperating precautions Alarm indicator Alarm Power indicator Power F1 dial, F2 dialParts and their functions Control panelCamera OSD button Camera OSD Preset MEMORY/MENU buttonsExit button Exit User buttons USER1, USER2FOCUS/PUSH OAF dial FOCUS/PUSH OAF Auto focus button AutoIris dial Iris Auto iris button AutoGround terminal Signal GND Power switch Power DC in socket DC 12Service switch SV/NM LAN connector LAN RJ-45 10BaseT/100BaseTXBasic operations of the unit Change the settings using the F1 dial and F2 dial Basic operations for the menusSelect the target menu Setting the unit Network settingsMAC Address 000Connections Example of IP connectionsConnections with the AW-HE50 and AW-HS50 Example of serial connections Connection with the AW-HE50Connection with the AW-HE100 Max m 3280 ft Connections with the AW-PH400 and cameraConnections with the AW-PH405 and camera Connection with the AW-PH650 Settings for connection with the remote cameras Serial connectionIP connection When setting the IP addresses for the first time Setting the IP addresses automatically auto IP settingAuto Setup Renew YESTurn the F2 dial, select Yes, and then press the F2 dial Auto Setup Keep IP Duplicate ERR Changing the IP addresses of the remote cameras Setting the IP addressesSelecting the camera group Group SelectAuto Setup ALL Clear Changing the IP address of the switcherChanging the camera numbers Clearing the IP address control tablesSet the Preset MEMORY/MENU 8 Button Camera to on Indicator lighting statuses and remote camera statusesSelecting the remote cameras to be operated Maintenance Power plug from the power outlet, and allow the unitTo cool down Unit mm inch AppearanceSpecifications Input/Output connectorAC adapter F0410Y0
Related manuals
Manual 48 pages 18.08 Kb

AW-RP50N specifications

The Panasonic AW-RP50N is a sophisticated remote camera controller designed for professional video production environments. Renowned for its advanced features and versatility, the AW-RP50N serves as an essential tool for operators needing precise control over multiple cameras in real-time.

One of the standout characteristics of the AW-RP50N is its ability to control up to 200 Panasonic cameras simultaneously. This feature is particularly beneficial in large-scale productions, such as broadcasting events, live concerts, and sports. It not only enhances operational efficiency but also provides cinematographers with a centralized point for camera management.

The AW-RP50N boasts a user-friendly interface, equipped with a large LCD touch panel that allows easy navigation and adjustment of camera settings. The intuitive layout makes it simple for operators to switch between camera feeds, adjust PTZ (pan-tilt-zoom) settings, and monitor video feeds without interruption. Customizable settings enable users to tailor the interface to suit their workflow preferences.

In terms of technology, the AW-RP50N supports multiple communication protocols, including IP (Internet Protocol) and serial communication. This flexibility allows integration with various camera models and third-party systems, offering a cohesive control experience. The unit is designed with robustness in mind, ensuring reliability even in demanding environments.

The AW-RP50N features advanced zoom and focus controls, providing smooth and precise movements essential for capturing high-quality video content. With programmable presets, operators can save specific camera angles and settings, making it easy to quickly switch back to preferred positions during production.

Additionally, it supports HD/SD video formats, catering to diverse production needs. The unit's compact design also makes it an ideal choice for mobile setups and small production teams that require portability without sacrificing performance.

Overall, the Panasonic AW-RP50N remote camera controller is a remarkable piece of technology, combining scalability, ease of use, and high-performance capabilities. Its robust feature set makes it an indispensable asset for professionals in the broadcasting and production industry, ensuring dynamic and reliable control of remote cameras in any situation. Whether scaling a large production or managing a small shoot, the AW-RP50N enables creators to achieve their artistic vision with precision and ease.
Top Page Image Contents