Axis Communications Q6042 PTZ user manual Smtp email, UPnPTM, RTP/H.264

Page 52

AXIS Q6042 PTZ Dome Network Camera

System Options

SMTP (email)

To send email messages from the Axis product via SMTP (Simple Mail Transfer Protocol), an SMTP mail server must be set up. This is done under System Options > Network > SMTP (email).

Enter the host names or IP addresses and port numbers for the primary and secondary mail servers in the fields provided. A From email address is also required. If the mail server requires authentication, check Use authentication to log in to this server and enter the necessary information.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 45. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 56.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

52

Image 52
Contents Axis Q6042 PTZ Dome Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q6042 PTZ Dome Network CameraReset to Factory Default Settings Connectors Performance ConsiderationsConnectors and Buttons Network ConnectorFor technical specifications, see Hardware OverviewLED Indicators Multi-connectorPower Button SD Card SlotMidspan LED Indicators Green Steady when AC power input connectedAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordControls on the Live View Live ViewClick Use Https Go to Setup Events Axis Media Control viewer toolbarManual Trigger To show the manual trigger buttons in the Live ViewPTZ Controls Speaker button Click to turn the speakers on or offAxis Q6042 PTZ Dome Network Camera Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingSet Up the Product Basic SetupVideo and Audio Video StreamPixel Counter ImageStream Profiles 264Camera Settings Exposure SettingsImage Appearance White BalanceImage Settings OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabGo to Video & Audio Overlay Image Use Overlay Text in an Action RuleGo to Events Action Rules Privacy Mask Audio SettingsAudio Modes Audio Input Audio ClipsAudio Output Axis Q6042 PTZ Dome Network Camera Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigOutput Buttons Preset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom GatekeeperConfiguration AutotrackingExclude Areas Max LimitsGuard Tour Tour RecordingTo add a guard tour To add a recorded tourOsdi Zones AdvancedLimits ControlsOperator Same as administrator but with lower priority Control QueueSet Up Motion Detection Windows DetectorsShock Detection Motion DetectionAudio Detection Install Application Go to Setup ApplicationsApplications Application LicensesAxis Q6042 PTZ Dome Network Camera Set Up Action Rules EventsConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers Actions Add RecipientsRecipient Types Set Up Email Recipients Recipient Use with actionSet Up Recurrences Create SchedulesTo create a new schedule Go to Events Schedules and click AddRecordings Recording ListContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages System Options SecurityUsers IP Address FilterCertificates IeeeGo to System Options Security Ieee To install a self-signed certificate Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeBasic TCP/IP Settings NetworkAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM Smtp emailUPnPTM RTP/H.264Storage BonjourSD Card Mount and Unmount SD CardPorts & Devices Network SharePorts Port StatusMaintenance SupportSupport Overview System OverviewReset to Factory Default Settings Plain ConfigScripting File UploadAxis Q6042 PTZ Dome Network Camera Multi-Connector Cable sold separately Cable provides the following connectorsFunction Pin Specifications To max 40 V DC, open drain, 100 mAConnector Troubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Video and image problems, generalSetup Video & Audio Camera Settings Key framesSettings Storage and disk management problemsNo audio Poor audio qualityTechnical Specifications Function/group Specifications Network Security Installation aidMaintenance PowerConnectors Performance ConsiderationsAxis Q6042 PTZ Dome Network Camera M4.2
Related manuals
Manual 68 pages 44.1 Kb

Q6042 PTZ specifications

The Axis Communications Q6042 PTZ is a sophisticated network camera designed for demanding surveillance environments. Known for its high-resolution imaging and advanced features, this camera is an ideal choice for monitoring large areas such as city centers, airports, and parking lots.

One of the standout features of the Q6042 is its 1080p resolution, offering crisp, detailed video quality. The camera supports H.264 compression technology, which minimizes bandwidth use and storage requirements without sacrificing image quality. This makes it very efficient for users looking to maintain high video fidelity while maximizing their network and storage capacity.

Another key characteristic of the Q6042 is its 18x optical zoom, enabling operators to zoom in on distant subjects without blurring the image. Combined with its advanced pan and tilt capabilities—offering a 360-degree continuous rotation and a tilt range of -20 to +90 degrees—the PTZ camera can cover vast areas and track moving objects with ease. This functionality is particularly useful for security personnel who need to monitor dynamic environments.

The Q6042 is also equipped with Axis' Wide Dynamic Range (WDR) technology, which enhances the camera's ability to capture clear images in challenging lighting conditions. This feature is vital when monitoring areas that experience significant contrasts in light, such as entrances and exits.

The camera is built for durability and features an IP66-rated weatherproof housing, protecting it from dust and heavy rain. It is also resistant to vandalism, making it suitable for outdoor installations where security is a prime concern.

Integrated with Axis’ Corridor Format technology, the Q6042 can be configured to monitor tall and narrow areas, optimizing the field of view for situations like hallways or alleys. This maximizes the effectiveness of surveillance and reduces the amount of unnecessary data captured.

Moreover, the Q6042 supports various network protocols and can be seamlessly integrated with other security systems. With its built-in analytics capabilities, the camera can be equipped with features such as motion detection and audio detection, allowing users to receive alerts based on specific events.

In summary, the Axis Communications Q6042 PTZ camera offers a robust solution for high-security surveillance needs, equipped with high-resolution video, extensive zoom capabilities, and advanced analytics, making it a versatile tool for modern security applications.