Axis Communications P5415E user manual Network, Basic TCP/IP Settings

Page 47

AXIS P5415–E PTZ Dome Network Camera

System Options

Network

Basic TCP/IP Settings

The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 55) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 47.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator) arp -s <IP address> <serial number>

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Axis P5415-E PTZ Dome Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P5415-E PTZ Dome Network Camera Table of ContentsConnectors Performance Considerations RJ45 Ethernet connector with Power over Ethernet Plus PoE+ Connectors and ButtonsNetwork Connector For technical specifications, seeLED Indicators Start a browser Internet Explorer, Firefox, Safari Access the ProductAccess from a Browser Click Use Https Access from the InternetSet the Root Password Manual Trigger Go to Setup EventsLive View Controls on the Live ViewAMC Audio Controls Axis Media Control viewer toolbarPTZ Controls To show the manual trigger buttons in the Live ViewAxis P5415-E PTZ Dome Network Camera Axis Media Control AMC How to Stream H.264Media Streams QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductImage Video and AudioVideo Stream 264 Click Save to apply the new settingsStream Profiles Camera SettingsDay/Night OverlayShutter & Gain Set Shutter toGo to Video & Audio Overlay Image Overlay ImageGo to Video & Audio Video Stream and select the Image tab Go to Events Action Rules Privacy MaskUse Overlay Text in an Action Rule Audio Input Audio SettingsAudio Modes Audio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewOutput Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis P5415-E PTZ Dome Network Camera Guard Tour Preset PositionsPTZ Pan Tilt Zoom GatekeeperFormats in the online help Osdi ZonesAdvanced LimitsControls Control QueueOperator Same as administrator but with lower priority Go to Detectors Motion Detection Set Up Motion Detection WindowsDetectors Motion DetectionMotion Detection Parameters Audio DetectionApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P5415-E PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesTriggers Recipient Types Add RecipientsActions Recipient Use with action Set Up Email RecipientsGo to Events Schedules and click Add Set Up RecurrencesCreate Schedules To create a new scheduleGo to Recordings List RecordingsRecording List Continuous RecordingClick Save to save and start the recording Languages IP Address Filter System OptionsSecurity UsersGo to System Options Security Ieee IeeeCertificates Date & Time To install a self-signed certificateGo to Setup System Options Security Certificates Click Install certificate and upload the certificateNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMSmtp email UPnPTMMount and Unmount SD Card StorageBonjour SD CardPort Status Ports & DevicesNetwork Share PortsSystem Overview MaintenanceSupport Support OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P5415-E PTZ Dome Network Camera Repainting the Camera Check the Firmware TroubleshootingUpgrade the Firmware Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsEmergency Recovery Procedure Problems setting the IP addressBasic Product is accessible locally but not externallyProblems with streaming H.264 Storage and disk management problems Video and image problems, generalSetup Video & Audio Camera Settings SettingsVideo cannot be recorded Technical Specifications Power Function/group Specifications Network SecurityInstallation Maintenance General CasingTerminal Connector ConnectorsFunction Pin Microphone/Line Performance ConsiderationsTip Audio InputM4.2
Top Page Image Contents