Axis Communications P3363-V user manual LED Indicators, Color Indication

Page 7

AXIS P3363–V Network Camera

Hardware Overview

Network connector - RJ45 Ethernet connector. Supports Power over Ethernet (PoE).

NOTICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 .

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for audio out.

SD card slot - A standard or high-capacity SD card (not included) can be used for local recording with removable storage.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Control button - The control button is used for:

•Resetting the product to factory default settings. See page 52.

•Connecting to an AXIS Video Hosting System service. See page 45. To connect, press and hold the button for about 1 second until the Status LED flashes green.

•Connecting to AXIS Internet Dynamic DNS Service. See page 46. To connect, press and hold the button for about 3 seconds.

I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications. In addition to an auxiliary power and a GND pin, the I/O terminal connector provides the interface to:

•Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

•Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

LED Indicators

LED

Color

Indication

 

 

 

Network

Green

Steady for connection to a 100 MBit/s network. Flashes for network activity.

 

 

 

 

Amber

Steady for connection to a 10 MBit/s network. Flashes for network activity.

 

 

 

 

Unlit

No network connection.

 

 

 

Status

Green

Steady green for normal operation.

 

 

 

 

Amber

Steady during startup and when restoring settings.

 

 

 

 

Red

Slow flash for failed upgrade.

 

 

 

Power

Green

Normal operation.

 

 

 

 

Amber

Flashes green/amber during firmware upgrade.

 

 

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Axis P3363-V Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P3363-V Network Camera Table of ContentsTechnical Specifications Hardware Overview ConnectorsHardware Overview Color Indication LED IndicatorsAxis P3363-V Network Camera Accessing the Product Accessing the ProductAccess from a Browser Network TCP/IP Advanced Accessing the Product Access from the InternetSet the Root Password Set Power Line FrequencyControls on the Live View Live ViewAxis Media Control viewer toolbar AMC Audio Controls PTZ ControlsAxis P3363-V Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Accessing Audio Streams Setting Up the Product Setting Up the ProductBasic Setup Image Video and AudioVideo and Audio Video Stream264 Stream ProfilesWhite Balance Video and Audio Camera SettingsExposure Settings Image AppearanceDay/Night Iris adjustmentView Area Set Shutter toGo to Video & Audio Overlay Image OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabFocus & Zoom Privacy MaskGo to Video & Audio Focus & Zoom Audio Modes Audio SettingsAudio Input Audio Output Audio ClipsLive View Config Live View ConfigDefault Viewer for Browsers Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis P3363-V Network Camera Guard Tour Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomLimits AdvancedControls Motion Detection DetectorsDetectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsRecommended values Default valuesAudio Detection Low level 0%Application Licenses Install ApplicationApplications ApplicationsAxis P3363-V Network Camera Events EventsPTZ Control Setting Up an Action RuleGo to Events Action Rules and click Add Go to Events Recipients and click Add RecipientsSchedules Recipient Use with actionGo to Events Recurrences and click Add Events RecurrencesContinuous Recording RecordingsRecordings Recording ListUsers System OptionsSystem Options SecurityGo to System Options Security Https IeeeCertificates CertificatesGo to System Options Security Ieee Audio Support Date & TimeGo to System Options Security Certificates Network Basic TCP/IP SettingsNTP Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Go to System Options Storage Click Network Share Ports & DevicesNetwork Share PortsSupport MaintenanceFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P3363-V Network Camera Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallyBasic Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsTechnical Specifications Technical SpecificationsConnectors Function/group Specifications System ApplicationAlarm actions PowerPerformance Considerations M2.3
Top Page Image Contents