Axis Communications P1425-E user manual UPnPTM, RTP/H.264, Bonjour

Page 45

AXIS P1425-E Network Camera

System Options

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 38. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 49.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

45

Image 45

Contents Axis P1425-E Network Camera Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis P1425-E Network Camera Table of ContentsPerformance Considerations Network Connector Connectors and ButtonsConnector Hardware OverviewSD Card Slot LED IndicatorsControl Button Status LED IndicationAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordLive View Set Power Line FrequencyControls on the Live View Click Use HttpsAxis Media Control viewer toolbar Go to Setup EventsPTZ Controls Manual TriggerAxis P1425-E Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P1425-E Network Camera Basic Setup Set Up the ProductVideo Set Up Video StreamsPixel Counter ImageClick Save to apply the new settings Stream Profiles264 Exposure Settings Camera SettingsImage Appearance White BalanceIris adjustment Set Shutter toDay/Night View Area Select an Aspect ratio and a Video stream resolutionOverlay Go to Video View AreaOverlay Image Use Overlay Text in an Action RuleGo to Video Overlay Image Focus & Zoom Privacy MaskGo to Events Action Rules Go to Video Focus & ZoomWhen satisfied, click Enable iris to enable the iris Default Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigOutput Buttons For more information about I/O ports, see I/O Ports onPTZ Pan Tilt Zoom Preset PositionsGuard Tour AdvancedControl Queue Camera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis P1425-E Network Camera Go to Setup Applications Install ApplicationApplications Application LicensesAxis P1425-E Network Camera Events Set Up Action RulesFallback Action Go to Events Action Rules and click AddAdd Recipients Set Up Email RecipientsCreate Schedules Go to Events Recipients and click AddGo to Events Recurrences and click Add Set Up RecurrencesRecording List RecordingsContinuous Recording Go to Recordings ListLanguages Security System OptionsUsers IP Address FilterIeee CertificatesGo to System Options Security Ieee Go to Setup System Options Security Certificates Basic TCP/IP SettingsClick Install certificate and upload the certificate Date & TimeIPv6 Address Configuration IPv4 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 BonjourSD Card StorageNetwork Share To add a network shareMaintenance Ports & DevicesSupport Logs & Reports System OverviewScripting File UploadPlain Config Reset to Factory Default SettingsUpgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Video Camera Settings Key framesStorage disruption Storage and disk management problemsRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Power Function/group Specifications System ApplicationConnectors DimensionsConnectors Performance Considerations M2.3