Axis Communications M3203 IPv4 Address Configuration, IPv6 Address Configuration, ARP/Ping

Page 39

AXIS M3203 Network Camera

System Options

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 46) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 39.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator)

arp -s <IP address> <serial number> ping -l 408 -t <IP address>

Windows example (this may require that you run the command prompt as an administrator)

arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125

4.Check that the network cable is connected and then restart the product by disconnecting and reconnecting power.

39

Image 39
Contents Axis M3203 Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis M3203 Network Camera Table of ContentsRJ45 Ethernet connector with Power over Ethernet PoE Connectors and ButtonsNetwork Connector For technical specifications, seeLED Indicators Control ButtonColor Indication Set the Root Password Accessing the ProductAccess from a Browser Access from the InternetSet Power Line Frequency Live ViewClick Create self-signed certificate Manual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbarPTZ Controls How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M3203 Network Camera Basic Setup Setting Up the ProductImage VideoVideo Stream Pixel Counter264 Camera SettingsClick Save to apply the new settings Stream ProfilesImage Appearance Exposure SettingsTo configure the view area View AreaGo to Video Overlay Image OverlayOverlay Image Go to Video Video Stream and select the Image tabUsing Overlay Text in an Action Rule Privacy MaskGo to Events Action Rules Axis M3203 Network Camera Browser Viewer Description Live View ConfigDefault Viewer for Browsers Viewer SettingsUser Defined Links Guard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControls AdvancedGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionRecommended values Default valuesMedium level 50% Low level 0%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis M3203 Network Camera Events Setting Up an Action Rule RecipientsGo to Events Action Rules and click Add Setting Up an Email Recipient Recipient Use with actionGo to Events Recipients and click Add Go to Events Schedules and click Add SchedulesRecurrences To create a new scheduleGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264To add a network share MaintenanceStorage Network ShareLogs & Reports SupportSupport Overview System OverviewReset to Factory Default Settings Plain ConfigFile Upload Upgrading the Firmware TroubleshootingFirmware To upgrade the product’s firmware Checking the FirmwareProduct cannot be accessed from a browser Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct is accessible locally but not externally Problems with streaming H.264Basic Storage and disk management problems Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsTechnical Specifications Connectors Function/group Specifications System ApplicationMaintenance Installation aids Memory PowerPerformance Considerations Function/group Specifications VideoM2.18
Related manuals
Manual 49 pages 16.78 Kb

M3203 specifications

Axis Communications is renowned for its innovative approach to network video technology, and its M3200 series is a testament to this legacy, comprising models such as the M3204-V, M3203-V, M3203, and M3204. These cameras are designed to meet the diverse needs of surveillance applications while maintaining high standards of video quality and performance.

One of the standout features of the M3200 series is its compact and discreet design. The cameras are ideal for indoor use in environments where aesthetics are vital, such as retail stores, hotels, and offices. Their unobtrusive form factor allows them to blend seamlessly into various settings while providing comprehensive monitoring capabilities.

The M3204-V and M3204 models support two-way audio, allowing users to not only monitor but also communicate through the camera. This feature is particularly useful for interactive communication in scenarios like customer service or security personnel directions. Additionally, it supports an audio input for connecting external microphones, which enhances situational awareness.

All models in the series are equipped with Axis’ Lightfinder technology, enabling them to capture high-quality video in low-light conditions. This technology ensures that users receive clear and detailed images even in challenging lighting environments. Furthermore, the M3200 series offers Wide Dynamic Range (WDR) functionality, which helps to enhance the visibility of both dark and bright areas in a scene simultaneously.

With support for1080p resolution at up to 30 frames per second, the M3200 series delivers crisp and detailed video, making identification easier. The cameras also feature H.264 compression technology, which helps optimize bandwidth and storage requirements without sacrificing quality.

For added versatility, the M3200 series includes a wide variety of mounting options, making it easy to install the cameras in various settings. They also come equipped with an IP51 rating for dust and drip protection, ensuring reliable operation even in less-than-ideal conditions.

Moreover, the integration of Axis' Zipstream technology efficiently compresses video, thereby decreasing storage and bandwidth usage while retaining critical forensic details. This is particularly beneficial for long-term archiving of footage without quality loss.

In conclusion, Axis Communications M3200 series models such as the M3204-V, M3203-V, M3203, and M3204 offer advanced features tailored for effective surveillance. The combination of compact design, enhanced low-light capabilities, flexible installation options, and superior image quality positions the M3200 series as a top choice for those seeking reliable and efficient security solutions.