Axis Communications AXIS 2420 user manual Installing the Audio Module

Page 40

40

 

The AXIS 2191 Audio Module

AXIS 2420 User’s Manual

Installing the Audio Module

Before installing the AXIS 2191 Audio Module, first install your network camera. Refer to the installation section of this manual. If you intend running the audio module in full-duplex mode, check that the sound card on your computer supports this.

If using an external microphone, connect it to the socket provided. To use an alternative input device, (e.g. CD-player or radio) connect it to Line-In on the terminal block.

Set the selector switch to Ext to use an external

microphone or device. Otherwise, set to Int to use the internal microphone.

Using the supplied cable, connect the audio module’s serial port to the net- work camera’s serial port.

Connect power to

the audio module.

Connect a loudspeaker to the 3.5mm socket (amplified speakers only), or to Out on the terminal block (speakers with no amplifica- tion). Other devices (including headphones) are connected to the terminal block.

Check that the power indicators on both the audio module and the camera are lit. Note that the power LED will blink during power-up.

Using a screwdriver, adjust the Volume In control so that the

Level In LED occasion-

ally shows yellow, but not red.

To verify the connection to the AXIS 2191,

start Internet Explorer and enter the IP address of the network camera in the loca- tion/address field, e.g. 171.1.2.200, as shown here. Configure the audio module from the camera’s administration pages, as described in the following section.

Image 40
Contents Axis Axis 2420 W/Lens Network Camera User’s Manual Safety Notices Support ServicesAbout This Document Legal ConsiderationsTable of Contents Deutsch Camera Models An Introduction to the AxisProduct Overview Features and Benefits An Introduction to the Axis Axis 2420 User’s ManualAxis 2420 User’s Manual An Introduction to the Axis An Introduction to the Axis Axis 2420 User’s Manual Physical Description Front PanelA Connector DC-Iris Connector Network IndicatorNetwork Connector B ConnectorMounting the Axis Checking The Hardware InventoryTitle/Variants Installing on a Network Shown below Window SyntaxExample Arp -s IP address Ethernet address temp ping IP addressVerifying and Completing the Installation From Your Browser SectionConnecting Your Computer Using the Null Modem Cable Installing via a Modem❿ Click Close Creating a Dial-Up Networking Connection ❷ Double-click the Make New Connection iconInitiating the Dial-Up Connection Refining the Dial-Up Networking PropertiesDial-Up Server ❸ In the Advanced options field, check Focusing Your Camera Configuring Your Camera Configuration Using the WizardsInstallation Wizard Using the Installation WizardUsing the Application Wizard Application WizardAdministration Tools Accessing the ToolsAdministration Tools Overview Settings Tool DescriptionApplications Tool Description Wizards DescriptionSupport Description HelpUser Access Rights System SecurityMotion Detection Creating a Motion Detection WindowSetting the RS-232 Port for use with a Modem COM-Ports, Modems and Pan-Tilt-Zoom DevicesUsing Pan-Tilt-Zoom Devices ModemInstallation Procedure Connecting PTZ DevicesDriver Tilt Bar Pan Bar Preset Home Positions Button Preset Positions Factory Default Settings Choosing Your Application Networking ApplicationsImage Compression Ratios Picture frequency for Networking ApplicationsMax fps Configuration Modem ApplicationsPicture Frequency for Modem Applications Proprietary ISP Dial-up ProtocolsInstallation and Configuration Overview Sequentially Uploading Images to an FTP Server/ISPUploading Pre and/or Post Alarm Images to an FTP server/ISP Viewing live Images in a Browser LAN/WANAxis 2191 Audio Module Features and FunctionsLegal Considerations Power Connector Power Indicator Normally lit VolumeTerminal Block Connector Level In/Level OutInstalling the Audio Module Configuring the Audio Module Admin ToolsUsing the Audio Module with Your Camera Using the Different Audio ModesFull-Duplex Half-DuplexSimplex Talk Simplex ListenTroubleshooting the Audio Module Possible causes Remedial actionsTechnical Specifications for the Axis Connection DiagramPinouts for the RS-232 Port Audio Module to Camera Serial CablePin Camera Appendix a Troubleshooting PINGing Your IP AddressPing Reply Interpretation and recommendation New IP addressSymptoms, Possible Causes and Remedial Actions Symptoms Possible causes Remedial actionsNetwork indicator Faulty cabling And/or To access the images, orWarranty Bad focus Focus has not been Displays redActiveX disabled Browser application Has not been disabled Java disabledEnabled in your browser Bad quality imagesAppendix B Other IP Setup Methods Method Operating Systems Refer to Axis IP InstallerInstalling the Axis IP Installer Using the Axis IP InstallerSetting the IP Address with Axis IP Installer Axis 2420 User’s Manual Other IP Setup Methods Appendix C Lenses and Advanced Focusing Fitting a LensDirect Focusing in Your Browser Using The Focus AssistantFocusing Quality ColorFocusing Procedure Plane of FocusAdjusting the DC-Iris Settings Other Advanced Parameters Exposure Control OverviewLens Options Description Adjusting the Back Focus ProcedureAppendix D Customizing Your Camera Configuration using FTPModifying the File System Custom Web Pages Customizing ProceduresCreating a New Home Fetch the boa.conf file, by typing Obtaining Updated Firmware Upgrading Appendix E Updating the FirmwareAppendix F The Unit Connectors RS-232 Serial ConnectorPinout Information PinSchematic Diagram I/O-A ConnectorThermal Sensor Schematic diagram showing possible application I/O-B ConnectorRS-485/422 B o External DC-Iris Connector Ethernet Network ConnectorBNC Video Output Control and MonitoringDigital Input Relay OutputQuerying the Status of the Digital Input Appendix G High-Speed Services Windows 2000 NAT-feature Network Address TranslationAvailable IP Addresses Routers and FirewallsAppendix H Technical Specifications Axis 2420 User’s Manual Technical Specifications Physische Beschreibung Bedienfeld vornDie Statusanzeige Status SeriennummerBedienfeld hinten A-AnschlussNetzwerkanschluss B-AnschlussÜberprüfen des Lieferumfangs Montage der AxisTeil Bez./Alternativ TeilInstallieren in einem Netzwerk ❷ Notieren Sie sich die auf der Unterseite derEin Befehlszeile ein Syntax Ping -t Kamera-IP-Adresse Ping IP-AdresseInstallieren in einem Netzwerk Axis 2420 User’s Manual Netzwerkanzeige NetworkAnschließen Ihres Computers über das Null-Modemkabel Anschließen an ein Modem❿ Klicken Sie auf Schließen Erstellen einer DFÜ-Netzwerkverbindung Den folgenden Beispielen als Name verwendetFeinabstimmung der DFÜ-Netzwerkeigenschaften Aufbauen einer DFÜ-VerbindungBzw. pass ein Scharfeinstellung der Kamera Werkseitige Standardeinstellungen Description du Materiel Panneau avantPanneau arrière Fixation de la caméra Axis Vérification de la liste du matérielElément Titre/Modèles Références Installation sur un réseau Des aiguilles dune montreVérification de l’installation à partir de votre navigateur Installation sur un réseau Axis 2420 User’s ManualInstallation par l’intermédiaire d’un modem ❿ Cliquez sur FermerCréation d’une connexion d’accès réseau à distance Le nom AxisCameraParamétrage des propriétés de l’accès réseau à distance Démarrage de la connexion d’accès réseau à distanceMise au point de votre caméra Vérification de la connexion modem❷ Réglez locculaire sur linfini F Au pointRestauration des paramètres d’usine par défaut Descripción física Panel frontalPanel posterior Comprobar el inventario de hardware Montar la AxisElemento Título/Variantes Referencias Cámara de red Axis 2420 PAL 0127-001-01Instalación de la cámara a una red Sólo Unix Teclee estos comandosSintaxis EjemploVerificando la instalación desde su buscador Instalación de la cámara a una red Axis 2420 User’s ManualConectar su ordenador usando el Cable de módem nulo Instalación de la cámara a un módem❿ Haga clic en Cerrar ❷ Haga doble clic en el icono Creación de un acceso telefónico a redes❻ Haga clic en OK para volver al Iniciando la conexión con marcación directa Ejemplos anteriores. Seleccione propiedadesVerificando la conexión de módem Enfocando la cámaraEs alcanzado Incluir los parámetros por defecto Bootp CCD IndexSmtp