Axis Communications AXIS M1144-L user manual Events, Set Up Action Rules, Triggers, Detectors

Page 31

AXIS M1144–L Network Camera

Events

Events

The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.

Set Up Action Rules

An action rule defines the conditions that must be met for the product to perform an action, for example record video or send an email notification. If multiple conditions are defined, all of them must be met to trigger the action.

For more information about available triggers and actions, see Triggers on page 31 and Actions on page 33.

The following example describes how to set up an action rule to record video to a network share if there is movement in the camera’s field of view.

Set up motion detection and add a network share:

1.Go to Detectors > Motion Detection and configure a motion detection window. See page 27

2.Go to System Options > Storage and set up the network share. See page 48.

Set up the action rule:

1.Go to Events > Action Rules and click Add.

2.Select Enable rule and enter a descriptive name for the rule.

3.Select Detectors from the Trigger drop-down list.

4.Select Motion Detection from the drop-down list. Select the motion detection window to use.

5.Optionally, select a Schedule and Additional conditions. See below.

6.Under Actions, select Record Video from the Type drop-down list.

7.Select a Stream profile and configure the Duration settings as described below.

8.Select Network Share from the Storage drop-down list.

To use more than one trigger for the action rule, select Additional conditions and click Add to add additional triggers. When using additional conditions, all conditions must be met to trigger the action.

To prevent an action from being triggered repeatedly, a Wait at least time can be set. Enter the time in hours, minutes and seconds, during which the trigger should be ignored before the action rule can be activated again.

The recording Duration of some actions can be set to include time immediately before and after the event. Select Pre-trigger time and/or Post-trigger time and enter the number of seconds. When While the rule is active is enabled and the action is triggered again during the post-trigger time, the recording time will be extended with another post-trigger time period.

For more information, see the online help .

Triggers

Available action rule triggers and conditions include:

•Applications – Use installed applications to trigger the rule. See Applications on page 29.

•Detectors

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Axis M1144-L Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis M1144-L Network Camera Table of ContentsConnectors Performance Considerations Symptoms, Possible Causes and Remedial ActionsHardware Overview Connectors and ButtonsNetwork Connector ConnectorColor Indication LED IndicatorsSD Card Slot Control ButtonSet the Root Password Access the ProductAccess from a Browser Access from the InternetManual Trigger Live ViewControls on the Live View Click Use HttpsTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar PTZ ControlsAxis M1144-L Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M1144-L Network Camera Basic Setup Set Up the ProductPixel Counter Click Save to apply the new settingsVideo Video Stream264 Stream ProfilesWhite Balance Camera SettingsExposure Settings Image AppearanceBuilt-in IR Illuminations LEDs To configure the view areaView Area OverlayGo to Video Overlay Image Overlay ImageGo to Events Action Rules Focus AdjustmentPrivacy Mask Use Overlay Text in an Action RuleBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsAdvanced Preset PositionsPTZ Pan Tilt Zoom Guard TourControl Queue Operator Same as administrator but with lower priorityGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection Windows Axis M1144-L Network Camera Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis M1144-L Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersSystem Input SignalHardware StorageActions Add RecipientsRecipient Types Create Schedules Set Up Email RecipientsGo to Events Schedules and click Add Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsFind Recordings Play RecordingContinuous Recording Export Video ClipGo to Recordings Continuous Languages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis M1144-L Network Camera Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserVideo Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalMotion Detection triggers unexpectedly Storage and disk management problemsTechnical Specifications Power Function/group Specifications Event actionsInstallation Maintenance General CasingFunction Pin Specifications ConnectorsPerformance Considerations Axis M1144-L Network Camera M2.13
Top Page Image Contents