Axis Communications AXIS M1144-L user manual Motion Detection triggers unexpectedly

Page 55

AXIS M1144–L Network Camera

Troubleshooting

Motion Detection triggers unexpectedly

Changes in luminance	Motion detection is based on changes in luminance in the image. This means that if there are
	sudden changes in the lighting, motion detection may trigger mistakenly. Lower the sensitivity
	setting to avoid problems with luminance.
Storage and disk management problems

Storage disruption	A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other
	read or write problems occur. To identify the source of the problem, check the System Log under
	System Options > Support > Logs & Reports. Depending on the problem, it might be necessary to
	re-mount the storage device.
	For information on how to set up a storage disruption alarm, see Events on page 31.
Video cannot be recorded	Check that the SD card is not write protected (that is, read only).
SD card cannot be mounted	Reformat the SD card and then click Mount.

NOTICE

Formatting the card will remove all content, including all recordings, from the SD card.

55

Image 55

Contents Axis M1144-L Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis M1144-L Network Camera Table of ContentsConnectors Performance Considerations Symptoms, Possible Causes and Remedial ActionsHardware Overview Connectors and ButtonsNetwork Connector ConnectorColor Indication LED IndicatorsSD Card Slot Control ButtonSet the Root Password Access the ProductAccess from a Browser Access from the InternetManual Trigger Live ViewControls on the Live View Click Use HttpsTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar PTZ ControlsAxis M1144-L Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M1144-L Network Camera Basic Setup Set Up the ProductPixel Counter Click Save to apply the new settingsVideo Video Stream264 Stream ProfilesWhite Balance Camera SettingsExposure Settings Image AppearanceBuilt-in IR Illuminations LEDs To configure the view areaView Area OverlayGo to Video Overlay Image Overlay ImageGo to Events Action Rules Focus AdjustmentPrivacy Mask Use Overlay Text in an Action RuleBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsAdvanced Preset PositionsPTZ Pan Tilt Zoom Guard TourControl Queue Operator Same as administrator but with lower priorityGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsAxis M1144-L Network Camera Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis M1144-L Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersSystem Input SignalHardware StorageActions Add RecipientsRecipient Types Create Schedules Set Up Email RecipientsGo to Events Schedules and click Add Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsFind Recordings Play RecordingContinuous Recording Export Video ClipGo to Recordings Continuous Languages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis M1144-L Network Camera Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserVideo Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalMotion Detection triggers unexpectedly Storage and disk management problemsTechnical Specifications Power Function/group Specifications Event actionsInstallation Maintenance General CasingFunction Pin Specifications ConnectorsPerformance Considerations Axis M1144-L Network Camera M2.13