Bosch Appliances 7000 manual Bosch Security Systems 2013.07 1.2.2 F.01U.283.679

Page 39

AutoDome 7000 Series (IP and HD)	Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts en 39

4.Hold the Pendant housing in position while tightening the two (2) 5-mm Allen head mounting screws on top of the housing to 10-12N-m(90-105in.-lbs).

Caution!

!You must tighten the two mounting screws to a minimum torque of 10-12 N-m (90‑105 in.-lbs) to ensure a proper seal between the arm and the housing.

Bosch Security Systems

Operation Manual

2013.07 1.2.2 F.01U.283.679

Image 39

Contents AutoDome 7000 Series IP and HD Page Table of contents Configuration Configuration via IP, Basic ModeConfiguration via IP, Advanced Mode Operation 139 14.32 Alarm Connections 116 14.33VCA 118About this Manual Safety ENSafety Precautions Important Safety InstructionsAutoDome 7000 Series IP and HD Safety EN en Coax grounding Important NoticesAutoDome 7000 Series IP and HD Safety EN en Informations FCC et Ices FCC & Ices InformationDisclaimer Customer Support and ServiceService Centers Connection in ApplicationsCanada Customer ServiceTechnical Support Repair CenterUnpacking Parts List, InstallationQuantity For Mount Type Supplied by Bosch? Tools RequiredAutoDome 7000 Series IP and HDUnpacking en Additional Products Required Barrel connector Roof parapet Mount Pipe MountOnly if installing a fiber optic model Necessary to install Autodome camerasSystem overview 4Pre-installation Checklist Extreme Mount Applications 1StabilizationPole and Mast Mounts Roof MountsRisk of electrostatic discharge Installing the Optional SD CardCard is optional Follow these stepsBosch Security Systems 2013.07 1.2.2 F.01U.283.679 Corner Mounts Mount Power Supply Box Wall, Mast Pole,Bosch Security Systems 2013.07 1.2.2 F.01U.283.679 Description Installing the Pendant Arm Wall, Corner, and MastRoute Wires and Attach Connectors Pole MountsAlarm and relay connectors Power Supply Box ConnectionsVAC Ground Screw P101 Connector Power In 120 VACCommunications Connector PinSerial Code CODE+ RXD TXDVG4-PSU1 / VG4-PSU2 Route Power through Intermediate Power Supply Box3 2 VG4-PA0 Power Supply Box Pendant Arm to Power Box Hinge Alignment Attach Pendant Arm to Power Supply BoxPendant Arm connections to Power Supply Box Make Connections in the Power Supply Box6Installing the VGA-PEND-WPLATE For a Corner installationFor a Mast or pole installation Attach the Pendant Arm to the Mounting Plate Ensure that the mounting plate is secure10 Pendant Arm Cables Route and Connect Wires to a Power Supply Box11 Mounting Plate Inside Detail Attach Pendant to Arm and Tighten Hook and drop Dome ConnectorRotate down to engage dome connector Tilt upBosch Security Systems 2013.07 1.2.2 F.01U.283.679 VGA-ROOF-MOUNT Installing the Roof Parapet and Pipe MountsVG4-A-PSU1 or VG4-A-PSU2 Power Supply Box Wiring the Power Supply Box VG4-A-PSU1/VG4-A-PSU2Pipe Interface Board Wiring the Fiber Optic Model Fiber Optic Ethernet Module installed Contro L IN/OUT Align Cover Door Hinge to Power Box Attach Cover Door to Power Supply BoxVGA-ROOF-MOUNT Installing the VGA-ROOF-MOUNTVGA-ROOF-MOUNT Bolt and attach both ends to anchor spots on the roof Installing the VG4-A-9543 Pipe Mount10 Pipe Mount 6Wire the Pipe Interface BoardPipe Interface Module Video Coax J102 BNCP105 J102 P102 P104 P107 J101 P106OUT + AWGCOM Pin Description Alarm Out Normally OpenRecessed hinge pin of the Dome Cap Connectors for any blocked pin holes and bent pinsAttach Pendant to Pipe and Tighten Interface Board Retaining Screws Pendant Mounting Screws14 Pendant to Roof / Pipe Mount Attachment Tilt DomeRight side of the box Connector P101 on the left side of the boxPrepare Suspension Ceiling for Installation Installing the In-Ceiling MountDimensions Prepare Drywall Ceiling for InstallationSuspension Ceiling Bracket Top View Tighten the four 4 securing screws to the Bracket AssemblyHole which will not be used to route wires Wire the Interface BoxInterface Box Connections Interface Box Connections OUT AgndCommuni GND CationsInstructions Installing the Ceiling IP54 Housing GasketIn-ceiling IP54 Rating Installation Diagram Attach Housing to the Interface Box10 Attach Housing to Interface Box 12 Secure camera to ceiling Secure Housing to CeilingRemove the foam inserts surrounding the camera module Remove the bubble from an in-ceiling housingRemove the bubble from a pendant housing Preparing the BubblePendant Bubble Release Opening Replace the trim ring optional In-ceiling modelsReplace the bubble in a pendant housing Replace the bubble in an in-ceiling housingConnection 11.1 Connecting the Autodome camera to the PC11.2 Power Cable and Wire Distances Guides Power 115/230 VAC Copper Wire To comply with local codes11.3 Ethernet Connections 11.4 Fiber Optic Ethernet Media Converter Optional 11.5 Alarms and Relay Connections AutoDome Programmed N.C.S Configuring a Normally Closed Supervised AlarmContact Alarm Condition Open Closed Normal Short Tamper AutoDome Programmed N.O.SAutoDome Programmed N.O Configuring Non-supervised Alarms inputs 3 throughConfiguring a Normally Open Non-supervised Alarm Configuring a Normally Closed Non-supervised Alarm11.6 Audio Connections Optional Wire Specifications Audio Line Level Input ConnectionsAudio Line Level Output Connections 12.1 System Requirements Configuration12.2 Configuring the Autodome 7000 Series Camera Using the Configuration ManagerUsing the Autodome 7000 Series Web Server Network Access Basic Mode menu About the SettingsStarting Configuration NavigationMaking Changes Activating Audio Reception 12.3 Configuring Audio OptionalPre-programmed User Modes Enabling Audio TransmissionConfirm password Configuration via IP, Basic Mode13.1 Basic Mode Device Access Password13.3 Basic Mode Network 13.2 Basic Mode Date/Time13.4 Basic Mode Encoder 13.5 Basic Mode Audio 13.6 Basic Mode Recording13.7 Basic Mode System Overview Camera ID Configuration via IP, Advanced Mode14.1 Advanced Mode General Identification See alsoDevice date/Device time PasswordDate/Time Date formatTime stamping 14.5 Display StampingDaylight saving time Camera name stamping14.6 Advanced Mode Web Interface Appearance 14.8 Livepage Functions Logging Advanced Mode Camera Installer MenuMax Frame Rate Option Available Streaming Options SC settingsReboot device Factory defaultsAdvanced ModeCameraEncoder Profile Encoder ProfileDSL Target bit rate Video resolutionExpert Settings Profile nameEncoder Streams Autodome IP Profiles Autodome HD Profiles Default profileMP SD SD stream options PropertyPrivacy Masks PreviewJpeg stream Camera Settings Maximum Gain Level Shutter ModeNight mode Fixed GainLens Settings PTZ Settings To define and edit an individual scene DiagnosticsPrepositions and Tours CompassSectors MiscellaneousLogs Pixel Counter Advanced Mode RecordingInput volume AudioStorage Management ISCSI Media Activating and Configuring Storage MediaDevice manager Recording mediaRecording Profiles Formatting Storage MediaDeactivating Storage Media Standard recording Maximum Retention Time Recording Scheduler Recording Status Number of destination IP address Advanced Mode Alarm Alarm ConnectionsConnect on alarm Destination passwordVideo output Video transmissionStream Remote portVCA Profiles Select On to activate audio alarms14.33 VCA Auto-connectVCA configuration PresetSelect Off or Test Motion detector MOTION+ only Alarm statusAggregation times Analysis typeSelect Area MOTION+ only Debounce time 1 s MOTION+ only2013.07 1.2.2 F.01U.283.679 Bosch Security Systems Global change Trigger delay sTamper detection SensitivityAppearing edges Virtual MasksReference Check Disappearing edgesName Audio AlarmAudio alarm Select On if you want the device to generate audio alarmsAlarm E-Mail Alarm Rules Alarm Task EditorAdvanced Mode Interfaces Alarm Inputs Alarm OutputsAdvanced Mode Network Network Access IPv6 Automatic IP assignmentIPv4 Fill in the 3 fields in this section of the screenTCP rate control Prefix lengthDNS server address 1 / DNS server address DetailsRCP+ port Interface mode ETHHttp browser port Https browser portHost name Enable DynDNSDynDNS ProviderAdvanced TCP port Quality of serviceUser Mode MulticastImage Posting Accounts 14.48 IPv4 FilterEncryption Advanced Mode Service Maintenance System Overview 192.168.0.10/resetMaintenance log LicensesDisplay Stamping 15.1 Using the Autodome CameraSettings, and to configure the network parameters OperationImage Selection Maximum Number of ConnectionsProtected AutoDome Protected NetworkSystem Log Preset ListDigital I/O Triggering RelayAux Control Tab Audio functionTo Enter a Keyboard Control Command To Set a Preset ShotTo View a Preset Shot Findhome Livepage Special FunctionsScan AutopanImage Resolution Processor LoadSelecting Recordings Export to FTP Controlling PlaybackBookmarks Mount/Mounting Surface Stability 15.2 Using Intelligent TrackingConfiguring Intelligent Tracking Guidelines for Implementing Intelligent TrackingOperation of Intelligent Tracking Using Intelligent TrackingField of View Unwanted MotionGuard Tours and Preset Tours Recommended Use of Your CameraContinuous Guard Tours Installation in an area with high humidity Preset ToursScene Illumination and Focus Settings Power-over-Ethernet PoEOutdoor installation SD cardUpgrading the AutoDome 800 Series Beginning the Firmware Update Process If camera’s IP address is not set, then TroubleshootingProblem Questions to Ask/Actions to Resolve the Problem If O.K., thenContact Bosch Technical Support Access the Settings Web page for the IP-enabled deviceExpand the Service Settings link, then click Network ON/OFFBubble Handling MaintenanceBubble Cleaning Cleaning the Bubble InteriorRemove an SD card Cleaning the Bubble ExteriorTechnical data Some of the following commands may not apply to your camera User Command TableAutoDome 7000 Series IP and HDUser Command Table en Index AutoDome 7000 Series IP and HD Index en En Index AutoDome 7000 Series IP and HD AutoDome 7000 Series IP and HD Index en Udpip UDP Page Bosch Security Systems, Inc

Related manuals

Manual 56 pages 38.94 Kb