Panasonic WV-CP470 Opening the Setup Menu, Editing the CAM SET UP Menu, All Reset Operation

SETUP

1. CAMERA SETUP MENU

This camera utilizes an on-screen user setup menu.

• Opening the Setup Menu

Press and hold down I for 2 seconds or more.

The CAM SET UP menu appears on the monitor as shown in the figure.

Check the current settings on the menu.

** CAM SET UP **			Highlighted
CAMERA ID	OFF	↵
ALC/ELC	ALC	↵
SHUTTER	---
AGC	ON(DNR-H)
SENS UP	OFF
SYNC	INT
WHITE BAL	ATW1↵
MOTION DET	OFF
LENS DRIVE	DC

END SET UP DISABLE

Refer to the following sections for a detailed

description of menu items. If you decide not to make any changes after checking the cur- rent settings, move the cursor to END in the bottom line, and press I to close the setup menu.

Note: If no button is pressed for 6 minutes while any of the setup menu is being displayed on the monitor screen, it is automatically closed and the mode returns to the normal camera picture.

2. SETUP OPERATION

This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM SET UP menu, use the following buttons on the side panel.

Left Button

Set Button

Up Button

Right Button

Down Button

Up Button (J): Moves the cursor upwards. Use this button to select an item or adjust the parameters.

Down Button (K): Moves the cursor downwards. Use this button to select an item or adjust the parameters.

Right Button (M): Moves the cursor to the right. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed.

Left Button (L): Moves the cursor to the left. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed.

Set Button (I: Executes selections and displays a submenu for an item with the N mark.

•To reset the parameter to the factory default setting, move the cursor to the parameter to be reset and press L and M simultaneously.

•To return to the previous menu or page, move the cursor to RET and press I.

•To close the setup menu, move the cursor to END and press I.

•All Reset Operation

All reset allows you to reset all setup menu items to the factory default settings if you are unsure about the correct settings. Proceed as follows:

(1)Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).

(2)While pressing both L and M, press I for a few seconds. The message ALL RESET momentarily appears on the monitor screen.

This resets all adjustments and parameters to the factory default settings.

•Editing the CAM SET UP Menu

Important Notice:

When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you can- not change the currently active settings. This is to prevent accidental changing of the settings.

To edit the CAM SET UP menu (change settings), press J and K or L and M to move the cursor to SET UP DIS- ABLE in the bottom line.

Press I. SET UP DISABLE changes to SET UP ENABLE. Move the cursor to END, then to the item(s) you want to change.

	** CAM SET UP **
CAMERA ID			OFF	↵
ALC/ELC			ALC	↵
SHUTTER			---
AGC			ON(DNR-H)
SENS	UP		OFF
SYNC			INT
WHITE BAL			ATW1↵
MOTION DET			OFF
LENS	DRIVE		DC
END
		SET	UP DISABLE

	** CAM SET UP **
CAMERA ID			OFF	↵
ALC/ELC			ALC	↵
SHUTTER			---
AGC			ON(DNR-H)
SENS	UP		OFF
SYNC			INT
WHITE BAL			ATW1↵
MOTION DET			OFF
LENS	DRIVE		DC
END
		SET	UP ENABLE

Important Notice:

When the setup menu is closed after changing the parameters in the menu, the new values are stored in the EEPROM (Electrically Erasable and Programmable Read-Only Memory). These values remain valid until new values are stored, even if the power of the camera is off.