Panasonic KX-HCM8 operating instructions How to turn on Network Camera for Installation

Page 20

Operating Instructions

2.3How to turn on Network Camera for Installation

Connect the DC plug of the AC adaptor to the DC IN jack and a category 5 straight/ cross cable to the Ethernet port. Connect the AC plug of the AC adaptor to the power outlet to turn on Network Camera. Ethernet Indicator turns on when the network is active.

	AC adaptor
Power
Outlet	DC plug

Connect a category 5 cable to the Ethernet port.

Notes

Thread the AC adaptor line through the hook downward.

•AC adaptor is used as the main disconnect device, so ensure that the power outlet is located/installed near the equipment and is easily accessible.

•Use only the specified Panasonic AC adaptor PQLV10 (Order No. PQLV10Y).

•When you set up Network Camera in [Type 3], connect it temporarily in [Type 1], [Type 2] or [Type 4].

•When the Ethernet Indicator is off, confirm that the Ethernet cable is properly connected, or PC, Ethernet hub or broadband router is properly working.

•Thread the AC adaptor line through the hook upward if it is convenient.

20

Image 20

Contents Network Camera Introduction For operation assistance CallTrademarks Network Camera MemoImportant Safety Instructions Table of Contents Index 115 Specification and TroubleshootingTechnical Guides Section Main Features Getting to Know Network CameraMulti-Language Display Update FirmwareAuthentication System Requirements Authentication-System Security Feature Authentication windowIncluded Accessories Setup CD-ROM Camera Feature Locations Front ViewRear View Bottom ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Type 2-Internet Connection with a Broadband RouterType 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCHow to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Network Camera Configuration Type Port No DefaultNetwork Parameters Table IP addressHow to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appearsSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade featureTop If Top Page does not appearOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Motion Jpeg Single CameraMulti-Camera HelpActiveX Controls Single Camera Screen Using Operation Bar Non Transfer mode Alarm/Timer mode Viewing Buffered Image ScreenViewer Clicking Start CapturePrimary SecondaryMulti-Camera Screen Setup Setup Administrator Camera SetupGo to Top Name/TimeFunctions of Network Camera Entered. If any operational issues are changed, tryThis option first. Refer to Go to Top Network Instructions for the data fields Enter only the numberDhcp Ddns File size of the imageName/Time CameraName DateAdjustment Time Changed AM/PM or 24HAuto Time ZoneSecurity Administrator Click Security Administrator on SetupRetype EnableFor Setup Password Click Security General User on Setup Security General UserNew User User ID ListDelete or Modify Top View Image Resolution Instructions for the data fields TopImage 160 x Image QualityImage Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer windowActive Time of Trigger Alarm enable conditionSets the image resolution and image quality Login timing Over write setting Data transfer methodSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Power Line White BalanceFixed Indoor FixedMulti-Camera Enable check box IP Address orURL * 1 or Host Camera NameClick External Output Control on Setup External Output ControlIndicator Control Status Restart Click Restart NowUpdate Firmware Click Update Firmware Operating Instructions Reset to Factory Default Click Reset to Factory Default on Setup Click ExecuteTechnical Guides Tripod Mounting MountingFlexible Stand Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Interfacing to the External I/O Explanation of External I/OPin Function External Sensor InputCircuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value NetworkImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Other Specification Description SpecificationsNetwork Camera Specifications Description SMTP, FTP Problem Cause and Remedy TroubleshootingAbout Network Camera Setup For Indicator Control window ISP Network window onAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen View Image Setting window on About Other TroublesConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP For product service When you ship the product