Panasonic KX-HCM8 Transfer in the Alarm Mode, Click Alarm on Image Transfer window

Page 64

Operating Instructions

Transfer in the Alarm Mode

The Alarm mode can transfer an image via e-mail or FTP when the alarm trigger is active. To activate the alarm trigger, the External Sensor Input of External I/O must be connected with the external sensors/devices. The Alarm mode can send the e-mail without transferring the image. The Alarm mode uses the Network Camera internal clock. Make sure Date and Time has been configured. Refer to page 54 about Date and Time.

1.Click [Alarm] on Image Transfer window.

a.

b.

c.

d.

e.

f.

64

Image 64

Contents Network Camera Introduction For operation assistance CallTrademarks Network Camera MemoImportant Safety Instructions Table of Contents Technical Guides Specification and TroubleshootingIndex 115 Section Main Features Getting to Know Network CameraAuthentication Update FirmwareMulti-Language Display System Requirements Authentication-System Security Feature Authentication windowIncluded Accessories Setup CD-ROM Camera Feature Locations Front ViewRear View Bottom ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Type 2-Internet Connection with a Broadband RouterType 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCHow to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Network Camera Configuration Type Port No DefaultNetwork Parameters Table IP addressHow to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appearsSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade featureTop If Top Page does not appearOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Motion Jpeg Single CameraMulti-Camera HelpActiveX Controls Single Camera Screen Using Operation Bar Non Transfer mode Alarm/Timer mode Viewing Buffered Image ScreenViewer Clicking Start CapturePrimary SecondaryMulti-Camera Screen Setup Setup Administrator Camera SetupGo to Top Name/TimeThis option first. Refer to Entered. If any operational issues are changed, tryFunctions of Network Camera Go to Top Network Instructions for the data fields Enter only the numberDhcp Ddns File size of the imageName/Time CameraName DateAdjustment Time Changed AM/PM or 24HAuto Time ZoneSecurity Administrator Click Security Administrator on SetupFor Setup Password EnableRetype Click Security General User on Setup Security General UserDelete or Modify User ID ListNew User Top View Image Resolution Instructions for the data fields TopImage 160 x Image QualityImage Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer windowSets the image resolution and image quality Alarm enable conditionActive Time of Trigger Login timing Over write setting Data transfer methodSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Power Line White BalanceFixed Indoor FixedMulti-Camera Enable check box IP Address orURL * 1 or Host Camera NameClick External Output Control on Setup External Output ControlIndicator Control Status Restart Click Restart NowUpdate Firmware Click Update Firmware Operating Instructions Reset to Factory Default Click Reset to Factory Default on Setup Click ExecuteTechnical Guides Flexible Stand Mounting MountingTripod Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Interfacing to the External I/O Explanation of External I/OPin Function External Sensor InputCircuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value NetworkImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Network Camera Specifications Description SpecificationsOther Specification Description SMTP, FTP About Network Camera Setup TroubleshootingProblem Cause and Remedy For Indicator Control window ISP Network window onAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen View Image Setting window on About Other TroublesConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP For product service When you ship the product